"Clearance" CNS Standards List| Compounded rubber | Salted Mei | Particulate bulk | Test Code | Micrographic Vocabulary | General Rule | Hydrochloric acid | Method Test | |
|
CNS 4380
2021 Edition Clearances and Creepage Distances for Control Gear 控制機構的絕緣距離 |
|
|
|
CNS 4370
2020 Edition Round Thread with Clearance and Flat Flank with Pitch 7mm (Limits of Size and Deviation--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙淺螺腹、螺距為７ｍｍ之限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 4245
2020 Edition Clearance Holes for Metric Bolts (1.6 up to and Including 150 mm Thread Diameter) 穿通孔徑（螺紋直徑1.6公釐~150公釐） |
|
|
|
CNS 4372
2020 Edition Round Thread with Clearance and Steep Flank with Pitch 7mm (Limits of Sizes and Deviations--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙，深螺腹，螺距７ｍｍ之螺紋限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 9574
2020 Edition Tolerances of Ball and Roller Bearings-Radial Clearance 滾動軸承公差（徑向間隙） |
|
|
|
CNS 493
2020 Edition Fine Whitworth Thread (Diameter Ranging From 20 to 189 mm, with Tip Clearance) 韋氏細螺紋（尖端有空隙，直徑自２０至１８９公釐） |
|
|
|
CNS 492
2020 Edition Whitworth Thread (Without Tip Clearance) 韋氏螺紋（尖端無空隙） |
|
|
|
CNS 10802
2018 Edition Single-Start and Double-Start Trapezoidal Screw Thread with Clearance for Railway Rolling Stock (Theoretical Values) 鐵路車輛用單頭與雙頭梯形螺紋（理論值） |
|
|
|
CNS 15620-5
2018 Edition Insulation coordination for equipment within low-voltage system – Part 5: Comprehensive method for determining Clearance and creepage distances equal to or less than 2 mm 低電壓系統下設備之絕緣協調－第5 部： 決定2 mm 以下空間距離及沿面距離之詳盡方法 |
|
|
|
CNS 4371
2017 Edition Round Thread with Clearance and Steep Flank with Pitch 7 mm Theoretic Values 圓螺紋（具有間隙、深螺腹、螺距為７ｍｍ之理論值） |
|
|
|
CNS 4369
2017 Edition Round Thread with Clearance and Flat Flank with Pitch 7 mm; Nominal Sizes 圓螺紋（具有間隙、淺螺腹，螺距為７ｍｍ之標稱尺寸） |
|
|
|
CNS 4371
1978 Edition Round Thread with Clearance and Steep Flank with Pitch 7 mm Theoretic Values 圓螺紋（具有間隙、深螺腹、螺距為7 mm之理論值） |
|
|
|
CNS 4369
1978 Edition Round Thread with Clearance and Flat Flank with Pitch 7 mm; Nominal Sizes 圓螺紋（具有間隙、淺螺腹，螺距為7 mm之標稱尺寸） |
|
| Find out:13Items | To Page of: First -Previous-Next -Last | 1 |
