"IT " CNS Standards List |
|
CNS 13352-2
2017 Edition Micrographics Vocabulary (Section 02: Image PosITions and Methods of Recording) 微縮技術詞彙（第二部：影像位置與縮攝方式） |
|
|
|
CNS 15210-3
2017 Edition Information technology - Radio frequency identification for ITem management - Part 3: Parameters for air interface communications at 13.56MHz 資訊技術－品項管理之無線射頻識別－第３部：１３.５６ＭＨｚ空中介面通信參數 |
|
|
|
CNS 327
2017 Edition Two-way Wrench Lever wITh Elliptical Handle 兩用扳柄，橢圓形桿端 |
|
|
|
CNS 13779
2017 Edition Measuring Methods for Infrared EmITting Diodes (IRED)(for Automation) 自動控制用紅外發光二極體量測法 |
|
|
|
CNS 14288
2017 Edition Method of measuring nITrided case depth for iron and steel 鋼鐵之氮化層深度測定法 |
|
|
|
CNS 4901
2017 Edition General Rules for ReliabilITy Assured Electronic Components 可靠度保證電子零組件通則 |
|
|
|
CNS 15977
2017 Edition Systems and software engineering – ArchITecture description 系統與軟體工程－架構描述 |
|
|
|
CNS 12074
2017 Edition Flash CavITy of Hot Forging Closed Die 熱鍛閉合模之餘料穴 |
|
|
|
CNS 2080
2017 Edition DolomITe 白雲石 |
Translated |
|
|
CNS 8672
2017 Edition Method of Test for Dry Reed SwITches(Carry Current) 乾式簧開關檢驗法（負載電流） |
|
|
|
CNS 8230
2017 Edition Method of Test for Dry Reed SwITches (Insulation Resistance) 乾式簧開關檢驗法（絕緣電阻） |
|
|
|
CNS 15832-1-1
2017 Edition Method of test for coating components − Part 1-1: General rule − Common test condITions 塗料成分試驗法－第1-1部：通則－一般試驗條件 |
|
|
|
CNS 541
2017 Edition Shovels wITh Point End 尖鏟 |
Translated |
|
|
CNS 13216
2017 Edition Hot - rolled High Strength Steel Sheets wITh Improved Formability for Automobile Structural Uses 熱軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 12749
2017 Edition Method of Test for SolubilITy of Aqueous Dyes for Paper 染紙用水溶性染料之溶解度試驗法 |
Translated |
|
|
CNS 11877
2017 Edition Phonograph Pick-Ups wITh 12.7mm Mounting １２．７ｍｍ安裝孔距之電唱機拾音器 |
|
|
|
CNS 13636
2017 Edition Steel Butt-welding Pipe FITtings 配管用鋼製對接銲接式管件 |
|
|
|
CNS 1203
2017 Edition Special Square File for SmITh 鐵工用特種四角銼 |
Translated |
|
|
CNS 4478
2017 Edition Slotted Set Screws wITh Chamfered End 有槽無頭去角端固定螺釘 |
|
|
|
CNS 505
2017 Edition ISO Metric Fine Screw Threads (Diameters from 42 to 300 mm and PITch 4 mm) 公制細螺紋8（ISO制）（標稱直徑42至300公釐，螺距4公釐） |
|
|
|
CNS 14819
2017 Edition Method of test for surface flammabilITy of materials using a radiant heatenergy source 材料表面耐燃燒性試驗法-輻射熱源垂直試驗法 |
|
|
|
CNS 13944
2017 Edition Method of preparing deposITed metal pad and samples for chemical analysis 化學分析用熔填金屬試驗材製作及取樣法 |
|
|
|
CNS 13546-1
2017 Edition Plastics − Methods for determining the densITy of non-cellular plastics − Part 3: Gas pyknometer method 塑膠－聚甲基丙烯酸甲酯(PMMA)模製及押出材料－第1部：命名系統及分類基準 |
|
|
|
CNS 15210-2
2017 Edition Information technology - Radio frequency identification for ITem management - Part 2: Parameters for air interface communications below 135kHz 資訊技術－品項管理之無線射頻識別－第２部：低於１３５ｋＨｚ空中介面通信參數 |
|
|
|
CNS 4657
2017 Edition Grub Screws wITh Thrust Point 無頭止推端螺釘 |
|
|
|
CNS 13420
2017 Edition Micrographics - First generation Silver - Gelatin Microforms of Source Docoments - DensITy Specifications 微縮攝影技術–拍攝文件之第一代銀鹽膠膜軟片–密度規格 |
|
|
|
CNS 9228
2017 Edition Method of Test for Dry Reed SwITches (Capacitance) 乾式簧開關檢驗法（電容量） |
|
|
|
CNS 15481-2
2017 Edition Road vehicles - Environmental condITions and testing for electrical and electronic equipment - Part 2: Electrical loads 道路車輛－電機電子配備環境條件與試驗－第２部：電力負載 |
|
|
|
CNS 10694
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Characteristics of the Measuring Equipment and Reference SensITivity) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（測量設備之特性及基準靈敏度） |
|
|
|
CNS 13807
2017 Edition Methods of Test of Epoxy for Light EmITting Diodes 發光二極體用環氧樹脂試驗法 |
|
| Find out:3948Items | To Page of: First -Previous-Next -Last | [93] [94] [95] [96] [97] [98] [99] |
