"A " CNS Standards List |
|
CNS 12244
2020 Edition GenerAl Requirements for Construction of Plastics Injection Molding Machines 塑膠射出成型機構造準則 |
|
|
|
CNS 2512
2020 Edition DeterminAtion of paper sizing − Stöckigt method 紙之上膠度試驗法－史托克法 |
|
|
|
CNS 14242
2020 Edition Method of test for peroxide number of Aviation turbine fuels 航空燃油過氧化物值測定法 |
|
|
|
CNS 1897
2020 Edition PotAssium Oxalate 過氯酸鉀（試藥） |
|
|
|
CNS 7525
2020 Edition Edible blended vegetAble oil 食用調合植物油 |
|
|
|
CNS 62282-3-201
2020 Edition Fuel cell technologies − PArt 3-201: Stationary fuel cell power systems − Performance test methods for small fuel cell power systems 燃料電池技術－第3-201部：定置型燃料電池發電系統－小型燃料電池發電系統之性能試驗法 |
|
|
|
CNS 14784
2020 Edition Method of test for trAce benzene in hydrocarbon solvents by capillary gas chromatography 石油溶劑微量苯試驗法（毛細管柱氣相層析法） |
|
|
|
CNS 15352
2020 Edition HArd anodic oxide coatings on aluminium and aluminium alloys 鋁及鋁合金之硬質陽極氧化膜 |
|
|
|
CNS 12616
2020 Edition Method of Test for ElectricAl Conductivity of Aviation and Distillate Fuels Containing a Static Dissipator Additive 航空燃油含靜電逸散劑導電度測定法 |
|
|
|
CNS 14104-4
2020 Edition Prosthetics And orthotics - Limb deficiencies - Part 3: Method of describing upper limb amputation stumps 義肢學與矯具學－肢體缺陷－第４部：導致截肢原因之描述 |
|
|
|
CNS 5270-5
2020 Edition GrAphical Symbols for Fluid Power Diagrams-Pressure Control Valve 液壓、氣壓圖形符號–壓力控制閥 |
|
|
|
CNS 7024
2020 Edition CAble Terminals for Automobiles (Type CA) 汽車用電線端子（塞型陽端子） |
|
|
|
CNS 3981
2020 Edition Dimensions of tApping screws thread 自攻螺釘螺紋尺度 |
|
|
|
CNS 15833
2020 Edition Low-emissivity coAted glass in building 建築用低輻射鍍膜玻璃 |
|
|
|
CNS 8051
2020 Edition Method of test for spices And condiments – Determination of degree of fineness of grinding – Hand sieving method 香辛料及調味料之檢驗法－研磨細度之測定(手篩法) |
|
|
|
CNS 4235
2020 Edition FAsteners－Acceptance inspection 結件之允收檢驗 |
|
|
|
CNS 396
2020 Edition TAper Pins 推拔銷 |
Translated |
|
|
CNS 15200-5-10
2020 Edition Methods of test for pAints – Part 5–10: Mechanical property of film - Abrasion resistance (Reciprocating test panel method) 塗料一般試驗法－第５－１０部：塗膜機械性質：耐磨耗性(試片往復法) |
|
|
|
CNS 15319-5
2020 Edition Sodium hydroxide for industriAl use - Part 5: Determination of silicon content - Inductively coupled plasma optical emission spectrophotometry 工業用氫氧化鈉－第５部：矽含量測定法－感應耦合電漿發光光譜分析法 |
|
|
|
CNS 24508
2020 Edition Ergonomics − Accessible design − Guidelines for designing tactile symbols and characters 人因工程學－無障礙設計－觸覺符號與字符之設計指導綱要 |
|
|
|
CNS 9567
2020 Edition WithdrAwal Sleeves for Rolling Bearings 滾動軸承拔出套筒 |
|
|
|
CNS 3-9
2020 Edition Engineering DrAwing(Symbols for Hydraulic and Pneumatic Power Systems) 工程製圖（液壓系氣壓系製圖符號） |
|
|
|
CNS 6904
2020 Edition CAble Terminals for Automobiles (Type LD) 汽車用電線端子（橫接叉型） |
|
|
|
CNS 14315
2020 Edition Methods of test for bending fAtigue of fine ceramics at room temperature 精密陶瓷室溫彎曲疲勞試驗法 |
|
|
|
CNS 7554
2020 Edition Slip-on Welding Steel Pipe FlAnges (10 kgf/㎠) 滑入熔接式鋼製管凸緣（10 kgf/㎠） |
|
|
|
CNS 121
2020 Edition CollAr (Using Heavy Duty Set Screws) 頸圈（用螺絲銷、重型） |
|
|
|
CNS 8930
2020 Edition SwitchgeArs, Contact - Spring Washers 加強型彈簧墊圈（電器開關–接觸用） |
|
|
|
CNS 2788
2020 Edition Fish PlAtes for Light Rails 輕型鋼軌用魚尾板 |
|
|
|
CNS 11638
2020 Edition Method of Inspection for Dimension of RefrActory Bricks 耐火磚尺度抽樣檢驗法 |
|
|
|
CNS 60227-6
2020 Edition Polyvinyl chloride inflAtable toys (replaced by CNS 4797、CNS 4797-1、CNS 4797-2、CNS 4797-3) 額定電壓450/750 V 以下聚氯乙烯絕緣電纜－第6部：升降機用電纜及可撓式連接用電纜 |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [93] [94] [95] [96] [97] [98] [99] |
