"For " CNS Standards List |
|
CNS 11067
2019 Edition Carbon and Alloy Steel Forgings for Pressure Vessels for Low Temperature Service 低溫壓力容器用碳鋼及合金鋼鍛鋼件 |
|
|
|
CNS 15725
2019 Edition Belt drives − Pulleys For V-belts (system based on datum width) − Geometrical inspection of grooves 皮帶傳動－使用三角皮帶之皮帶輪(以基準寬度為基礎之系統)－溝槽之幾何檢驗 |
|
|
|
CNS 4987
2019 Edition Methods of Test For Physical Properties of Synthetic Detergents 合成清潔劑之物理性檢驗法 |
Translated |
|
|
CNS 14631
2019 Edition Structural sawn lumber used in platForm construction 框組壁工法結構用製材 |
|
|
|
CNS 29182-5
2019 Edition InFormation technology − Sensor networks: Sensor Network Reference Architecture (SNRA) − Part 5: Interface definitions 資訊技術－感測器網路：感測器網路參考架構(SNRA)－第5部：介面定義 |
|
|
|
CNS 15779
2019 Edition InFormation technology − Automatic identification and data capture techniques − GS1 DataBar bar code symbology specification 資訊技術－自動識別與資料擷取技術－GS1 DataBar 條碼符號表示法 |
|
|
|
CNS 11069
2019 Edition Iron and steel－Methods For determination of Carbon content 鐵及鋼－碳定量法 |
|
|
|
CNS 5812
2019 Edition Methods of Test For Peel Strength of Adhesives 黏著劑之剝離強度測定法 |
|
|
|
CNS 9991
2019 Edition Fixed Design and Method of Use For Oil Seals for Automobiles 汽車用油封安裝部位之設計及使用方法 |
|
|
|
CNS 3666
2019 Edition Method of Magnetic Particle Flaw Detection Test For Ferromagnetic Materials 鋼鐵材料之磁粉探傷法 |
|
|
|
CNS 14934-5
2019 Edition Electromagnetic compatibility (EMC) - Limits - Part 5: Limitation of voltage fluctuations and flicker in low-voltage power supply systems For equipment with rated current greater than 16A 電磁相容－限制值－第5部：額定電流大於16 A之設備於低電壓電源系統中電壓變動及閃爍之限制值 |
|
|
|
CNS 8110
2019 Edition Marine Forged Steel Globe Valves for Compressed Air 船用鍛鋼壓縮空氣球形閥 |
|
|
|
CNS 14128
2019 Edition Method of impact test For instrument panel of passenger cars 小客車用儀表板衝擊試驗法 |
|
|
|
CNS 61850-7-420
2019 Edition Communication networks and systems For power utility automation − Part 7-420: Basic communication structure − Distributed energy resources logical nodes 電力公用事業自動化之通訊網路及系統－第7-420部：基本通訊結構－分散式能源邏輯節點 |
|
|
|
CNS 3473
2019 Edition Hydraulic brake wheel cylinders For automobiles 汽車用液壓煞車分泵 |
|
|
|
CNS 13306-2-3
2019 Edition Specification For radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements 射頻擾動和免疫力量測設備與量測方法－第２－３部：擾動和免疫力量測方法－輻射擾動量測 |
|
|
|
CNS 15176-26-1
2019 Edition Wind turbines − Part 26-1: Time-based availability For wind turbine generating systems 風力機－第26-1 部：風力發電機系統以時間為基礎之可利用率 |
|
|
|
CNS 15200-1-6
2019 Edition Testing methods For paints - Part 1-6: General rule - Temperatures and humidities for conditioning and testing 塗料一般試驗方法－第１－６部：通則－調節與試驗之溫度及濕度 |
|
|
|
CNS 12770
2019 Edition Method of Test For Buoyant Smoke Signal for Marine Use 船用浮煙信號設備檢驗法 |
|
|
|
CNS 20349-1
2019 Edition Personal protective equipment − Footwear protecting against risks in foundries and welding − Part 1: Requirements and test methods For protection against risks in foundries 個人防護具－防止鑄造及熔接中風險之鞋類－第1部：防護鑄造中風險之要求事項及試驗方法 |
|
|
|
CNS 14118
2019 Edition Emergency shut-off valves For nature gas with high pressure and intermediate pressure 高、中壓天然氣用緊急遮斷閥 |
|
|
|
CNS 15449-2-101
2019 Edition Safe requirements For electrical for measurement, control and laboratory use ? Part 2-101: Particular requirements for in vitro diagnostic (IVD) medical equipment 量測、控制及實驗室使用電氣設備安全規定－第2-101 部:體外診斷(IVD)醫用設備之個別規定 |
|
|
|
CNS 13161
2019 Edition Codes For units of measure used in international trade 國際貿易之計量單位代碼 |
|
|
|
CNS 14937
2019 Edition Method of test For effects of heat and air on asphaltic materials (Thin-film oven test) 柏油材料受熱及空氣影響試驗法（薄膜烘箱法） |
|
|
|
CNS 13018
2019 Edition Plastic film capacitors (characteristic S) For direct current 塑膠製平墊板 |
|
|
|
CNS 12456
2019 Edition Corrosion Inhibitor For Reinforcing Steel in Concrete 鋼筋混凝土用防銹劑 |
|
|
|
CNS 9892
2019 Edition Rubber materials For vibration isolators 隔振橡膠材料 |
|
|
|
CNS 6959
2019 Edition Acid and Heat Resisting Bricks For Chemical Industry 化學工業用耐酸耐熱磚 |
|
|
|
CNS 14545-1
2019 Edition Fire hazard testing-part 1:Guidance For assessing fire hazard of electrotechnical products(general guidance) 火災危險性試驗－第１部：評估電氣產品火災危險性的指引（通則） |
|
|
|
CNS 6337
2019 Edition General Rules For Test of Tungsten and Molybdenum Materials for Lighting and Electronic Equipments 照明及電子設備用鎢鉬材料試驗通則 |
|
| Find out:9607Items | To Page of: First -Previous-Next -Last | [88] [89] [90] [91] [92] [93] [94] |
