"A " CNS Standards List |
|
CNS 4547
2020 Edition Limits of Sizes And Tolerances for ISO Metric Fine Screw Threads (Tolerance Quality: Medium,Tolerances: 6H and 6h、6g)(Diameters from 2.5 to 300mm and Pitches 0.35 to 6mm) 公制細螺紋限界尺寸及公差(ISO制)(中品級–6H、6h、6g)(標稱直徑2.5至300mm,螺距0.35至6mm) |
![]() |
|
|
CNS 60227-7
2020 Edition Polyvinyl chloride insulAted cables of rated voltages up to and including 450/750 V − Part 6: Lift cables and cables for flexible connections 額定電壓450/750 V 以下聚氯乙烯絕緣電纜-第7部:兩心或多心遮蔽與無遮蔽可撓式電纜 |
![]() |
|
|
CNS 16139-1
2020 Edition StAtistics − Vocabulary and symbols − Part 1: General statistical terms and terms used in probability 統計學-詞彙與符號-第1部:一般統計用語及機率用語 |
![]() |
|
|
CNS 2751
2020 Edition Method of test for volAtility of liquefied petroleum gases 液化石油氣揮發性試驗法 |
![]() |
|
|
CNS 4548
2020 Edition Limits of Sizes And Tolerances for ISO Metric Fine Screw Threads (Tolerance Quality: Coarse,Tolerances: 7H and 8g)(Diameters from 4 to 300mm and Pitches 0.5 to 6mm) 公制細螺紋限界尺寸及公差(ISO制)(粗品級–7H、8g)(標稱直徑4至300mm,螺距0.5至6mm) |
![]() |
|
|
CNS 4372
2020 Edition Round ThreAd with Clearance and Steep Flank with Pitch 7mm (Limits of Sizes and Deviations--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋(具有間隙,深螺腹,螺距7mm之螺紋限界尺寸和偏差螺紋量規之公差和許可磨損) |
![]() |
|
|
CNS 11278
2020 Edition End-hArdened Rails 端部熱處理鋼軌 |
![]() |
|
|
CNS 619
2020 Edition Method of Test for Apparent Porosity, Water Absorption and Specific Gravity of Refractory Bricks 耐火磚視孔隙度、吸水率及比重試驗法 |
![]() |
|
|
CNS 154
2020 Edition LArge Unfinished Washers (for Metric Bolts and Nuts: M6 - M52) 粗製大墊圈(用於公制螺栓及螺帽M6至M52) |
![]() Translated |
|
|
CNS 15787
2020 Edition Method of fillet weld test for welding consumAbles 銲接材料之填角銲試驗法 |
![]() |
|
|
CNS 495
2020 Edition TAper Pipe Threads 推拔管螺紋 |
![]() |
|
|
CNS 20889
2020 Edition Printing SpecificAtions for Optical Character Recognition 隱私增強資料去識別化術語與技術分類 |
![]() |
|
|
CNS 17011
2020 Edition Conformity Assessment – Requirements for accreditation bodies accrediting conformity assessment bodies 符合性評鑑-認證機構認證符合性評鑑機構之要求事項 |
![]() |
|
|
CNS 15355
2020 Edition Test method for determinAtion of mass per unit area of anodic oxide coatings on aluminium and aluminium alloys -Gravimetric method 鋁及鋁合金之陽極氧化膜單位面積質量試驗法-重量分析法 |
![]() |
|
|
CNS 13005
2020 Edition Welding consumAbles − Solid wires and rods for TIG welding of mild steels, high strength steels and low temperature service steels 銲接材料-軟鋼、高強度鋼及低溫用鋼TIG銲接用實心線及填料棒 |
![]() |
|
|
CNS 9558
2020 Edition Round-steel link chAins for hoisting equipments, calibrated, tested, short linked 起重設備用圓鋼製短環環鏈 |
![]() |
|
|
CNS 532
2020 Edition Limits of Size And Tolerances for ISO Metric Coarse Screw Threads (Tolerance Quality:Fine,Tolerances:4H、5H and 4h)(Diameters from 1 to 68 mm and Pitches 0.25 to 6 mm) 公制粗螺紋限界尺寸及公差(ISO制)(細品級–4H、5H、4h)(標稱直徑1至68mm,螺距0.25至6mm) |
![]() |
|
|
CNS 17881-2
2020 Edition Textiles − DeterminAtion of certain flame retardants − Part 2: Phosphorus flame retardants 紡織品-阻燃劑測定法-第2部:磷系阻燃劑 |
![]() |
|
|
CNS 15389
2020 Edition LeAther - Physical and mechanical tests - Determination of tear load - Double edge tear 皮革-物性及機械性質測試-雙邊撕裂強度試驗法 |
![]() |
|
|
CNS 15817
2020 Edition Edible cAmellia seed oil 食用苦茶油(油茶油) |
![]() |
|
|
CNS 14104-1
2020 Edition Prosthetics And orthotics - Classification and description of prosthetic components - Part 3: Description of upper-limb prosthetic components 義肢學與矯具學-肢體缺陷-第1部:先天性肢體缺陷之描述 |
![]() |
|
|
CNS 5818
2020 Edition Rubber compounding ingredients − CArbon black − Determination of iodine adsorption number 橡膠配合劑-碳黑-碘吸附值之測定 |
![]() |
|
|
CNS 6611
2020 Edition Method of test for meAt and meat products – Determination of total phosphorus content 肉及肉製品檢驗法-總磷含量之測定 |
![]() |
|
|
CNS 2832
2020 Edition Edible sesAme oil 食用芝麻油 |
![]() |
|
|
CNS 62498-3
2020 Edition RAilway applications − Environmental conditions for equipment − Part 3: Equipment for signalling and telecommunications 鐵路應用-設備之環境條件-第3部:號誌及電訊設備 |
![]() |
|
|
CNS 6752
2020 Edition GlossAry of Terms Relating to Parts of Metal Sawing Machines 鋸床、切斷機主要零件詞彙 |
![]() |
|
|
CNS 16148
2020 Edition Textile child cAre articles − Safety requirements and test methods for children's sleep bags for use in a cot 紡織類兒童照護用品-嬰兒床用嬰幼兒睡袋安全要求與試驗法 |
![]() |
|
|
CNS 15378-2
2020 Edition Fine cerAmics - Test method for self-cleaning performance of photocatalytic materials - Part 2: Decomposition of wet methylene blue 精密陶瓷—光觸媒材料之自我潔淨性能測定法—第2部:濕式亞甲基藍分解性能 |
![]() |
|
|
CNS 4670-21
2020 Edition Specified Items for MAchine Tools - Gear Shapers (Rack Cutter Type) 工具機規範之項目–齒輪刨製機(齒條刨刀型) |
![]() |
|
|
CNS 2432
2020 Edition Corn (ZeA mays) 玉米 |
![]() |
Find out:15242Items | To Page of: First -Previous-Next -Last | [85] [86] [87] [88] [89] [90] [91] |