"f " CNS Standards List |
|
CNS 12244
2020 Edition General Requirements for Construction of Plastics Injection Molding Machines 塑膠射出成型機構造準則 |
|
|
|
CNS 3-16
2020 Edition Engineering Drawing (Geometrical Tolerancing - Principles and Methods of Verification) 工程製圖（幾何公差–檢測原理與方法） |
|
|
|
CNS 15804
2020 Edition Oil of cassia, Chinese type − Determination of trans-cinnamaldehyde content − Gas chromatographic method on capillary columns 肉桂油(中國型)－反桂皮醛含量測定法－毛細管柱氣相層析法 |
|
|
|
CNS 6903
2020 Edition Cable Terminals for Automobiles (Type LB) 汽車用電線端子（橫接環眼型） |
|
|
|
CNS 11423
2020 Edition Method of Test for Grain Size of Refractory Mortar 耐火墁料細度試驗法 |
|
|
|
CNS 12514-11
2020 Edition fire-resistance tests − Elements of building construction − Part 11: Specific requirements for the assessment of fire protection to structural steel elements 建築物構造構件耐火試驗法－第11部：鋼結構構件防火被覆評估特定要求 |
|
|
|
CNS 8233
2020 Edition Tyre Valve Thread for Automobiles 汽車輪胎氣門嘴螺紋 |
|
|
|
CNS 30128
2020 Edition Information technology − Sensor networks − Generic sensor network application interface 資訊技術－感測器網路－ 通用感測器網路應用介面 |
|
|
|
CNS 7024
2020 Edition Cable Terminals for Automobiles (Type CA) 汽車用電線端子（塞型陽端子） |
|
|
|
CNS 12983
2020 Edition Standard Substances for Volumetric Analysis 容量分析用標準試藥 |
|
|
|
CNS 4797-6
2020 Edition Safety of toys − Part 6: Organic chemical compounds − Requirements 玩具安全－第6部：有機化合物－要求事項 |
|
|
|
CNS 15227
2020 Edition Single-use medical examination gloves - Part 1: Specification for gloves made from rubber latex or rubber solution 單次使用之醫用檢驗手套－第１部：以乳膠或橡膠溶液製成之手套規格 |
|
|
|
CNS 3325
2020 Edition Standard Classification of Castable Refractories 可鑄耐火物分級標準 |
|
|
|
CNS 5786
2020 Edition Electric Windshield Washers for Automobiles 汽車擋風玻璃電動噴洗器 |
|
|
|
CNS 1887
2020 Edition Potassium fluoride(Reagent) 六氰鐵（Ⅲ）酸鉀（試藥） |
|
|
|
CNS 4238
2020 Edition finishes and Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 9746
2020 Edition Method of Test for Potential Expansion of Portland Cement Mortars Exposed to Sulfate 卜特蘭水泥墁料暴露於硫酸盬中之潛在膨脹檢驗法 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 13167
2020 Edition Safety Standards for Construction of Spindle Shapers 立軸機之構造安全基準 |
|
|
|
CNS 4532
2020 Edition Terms Relating to the End (Point) of Fasteners 結件端部詞彙 |
|
|
|
CNS 330
2020 Edition Hand Wheels of Low Heat Insulation Materials 手輪（以低導熱材料製成） |
|
|
|
CNS 13169
2020 Edition Safety Standards for Construction of Veneer Lathes 單板旋切機之構造安全基準 |
|
|
|
CNS 15374
2020 Edition Liquefied petroleum gases - Determination of dissolved residues (High-temperature gas chromatographic method) 液化石油氣－可溶殘餘物測定法（高溫氣相層析法） |
|
|
|
CNS 3-2
2020 Edition Engineering drawing (Conventional representation of machine elements) 工程製圖（機械元件習用表示法） |
|
|
|
CNS 5270-1
2020 Edition Graphical Symbols for Fluid Power Dizgrams-Line and Connection 液壓、氣壓圖形符號–管路及連接 |
|
|
|
CNS 1947
2020 Edition Sodium Bisulfate, Fused 化學試藥（融熔硫酸氫鈉） |
|
|
|
CNS 14104-4
2020 Edition Prosthetics and orthotics - Limb deficiencies - Part 3: Method of describing upper limb amputation stumps 義肢學與矯具學－肢體缺陷－第４部：導致截肢原因之描述 |
|
|
|
CNS 15832-4-2
2020 Edition Method of test for paint components − Part 4-2: Analysis for components emitted from film − Volatile organic compounds 塗料成分試驗法－第4-2 部：塗膜釋出成分分析－揮發性有機化合物(VOC) |
|
|
|
CNS 13601
2020 Edition Method of test for flammability of children's sleepwear 兒童睡衣防焰性試驗法 |
|
|
|
CNS 3333
2020 Edition Zinc alloy ingots intended for castings 鑄造用鋅合金錠 |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [80] [81] [82] [83] [84] [85] [86] |
