"SI " CNS Standards List |
|
CNS 13064
2017 Edition Methods of Test for Specific Gravity of Epoxy ReSIns and Hardeners 環氧樹脂及硬化劑比重測定法 |
![]() |
|
|
CNS 13068
2017 Edition Methods of test for total amine values of amine-based hardeners of epoxy reSIns 環氧樹脂之胺系硬化劑總胺價試驗法 |
![]() Translated |
|
|
CNS 12866
2017 Edition BaSIc Environmental Testing Procedures Part 2 : Tests-Test Z/AM : Combined Cold/Low Air Pressure Tests 環境試驗法(電氣、電子)–低溫/低氣壓複合試驗法 |
![]() |
|
|
CNS 7197
2017 Edition BaSIc Dimensions of 5 kgf/㎠ Ferrous Materials Pipe Flanges 鐵金屬製管凸緣基準尺度(5 kgf/㎠) |
![]() |
|
|
CNS 12564
2017 Edition Method of Test for Fiber Optic Devices (FOTP-172 Flame ReSIstance of Firewall Connector) 光纖裝置檢驗法(防火牆連接器之防火試驗FOTP–172) |
![]() |
|
|
CNS 4369
2017 Edition Round Thread with Clearance and Flat Flank with Pitch 7 mm; Nominal SIzes 圓螺紋(具有間隙、淺螺腹,螺距為7mm之標稱尺寸) |
![]() |
|
|
CNS 386-1
2017 Edition Test SIeves - For construction engineering 試驗篩-營建工程用 |
![]() |
|
|
CNS 14492-1
2017 Edition Methods of measurement on radio receivers for various classes of emisSIon-Part1:General considerations and methods of measurement,including audio-frequency measurements 不同發射類別之無線電接收機的量測方法-第1部:概論及含括音頻量測在內的量測方法 |
![]() |
|
|
CNS 3455
2017 Edition Method of test for milk and milk products - Determination of viscoSIty in condensed milk 乳品檢驗法-煉乳黏度之測定 |
![]() |
|
|
CNS 13788
2017 Edition Methods of Test for Water Vapor TransmisSIon Rate of Plastic Films and Sheets (Instrument Method) 塑膠薄膜及薄片透濕度試驗法(儀器法) |
![]() Translated |
|
|
CNS 13063
2017 Edition General Rules for Methods of Test for Epoxy ReSIns and Hardeners 環氧樹脂及硬化劑試驗法總則 |
![]() |
|
|
CNS 9240
2017 Edition Method of Test for Low Freguency(Below 3 MHz) Electrical Connectors(TP - 18 Visual and DimenSIonal Inspection) 頻率3MHz以下電連接器檢驗法(外觀及尺度檢查TP–18) |
![]() |
|
|
CNS 13623
2017 Edition Test Methods for Measuring ReSIstivity,Hall Coefficient and Determining Hall Mobility in Single-Crystal Semiconductors(Van Der Pauw Method) 單晶片之電阻率、霍爾係數及霍爾移動率之測定法(范德普法) |
![]() |
|
|
CNS 6135-12
2017 Edition Heading aids-Part12: DimenSIons of electrical connector systems 助聽器-第12部:電氣連接系統之尺寸 |
![]() |
|
|
CNS 11446-1
2017 Edition Method of measurement on receives for televiSIon broadcast transmission - Part 1: General considerations - Measurements at radio and video frequencies 電視廣播傳輸接收機之量測方法-第一部:概論-射頻及視頻之量測 |
![]() |
|
|
CNS 8214
2017 Edition Testing Method of OutSIde and Inside Diameters Wrapped Bushes for Plain Bearing 滑動軸承用捲製軸承襯檢驗法(外徑及內徑) |
![]() |
|
|
CNS 5052
2017 Edition SIngle Coil Spring Lock Washers for Cylindrical Head Screws 單圈彈簧墊圈(柱頭螺釘用) |
![]() |
|
|
CNS 14409
2017 Edition Sound and televiSIon broadcast receivers and associated equipment - Immunity characteristics - Limits and methods of measurement 聲音與電視廣播接收機及相關設備-免疫力特性-限制值與量測方法 |
![]() Translated |
|
|
CNS 5535
2017 Edition Small Switch for SIngle-phase Motors 單相電動機用小型開關 |
![]() Translated |
|
|
CNS 14715
2017 Edition Electric reSIstance welding-Integrated transformers for welding guns 工業用機器人電阻銲接—銲槍之變壓器 |
![]() |
|
|
CNS 14546
2017 Edition LED traffic SIgnal lanterns and lamp housing 發光二極體交通號誌燈燈面及燈箱 |
![]() |
|
|
CNS 1019
2017 Edition Picks (SIngle), One Taper End and One Hammershaped End 單十字鎬(僅具單一斜錐狀端部) |
![]() |
|
|
CNS 10901
2017 Edition Method of Test for Terminal Blocks for Industrial and SImilar Use 工業用接線板檢驗法 |
![]() |
|
|
CNS 13625
2017 Edition Product analySIs and its tolerance for wrought steel 圓形砷化鎵單晶片產品標準 |
![]() |
|
|
CNS 5150
2017 Edition Photography-ProcesSIng chemicals -Specifications for hydroquinone 照相術─顯像處理化學品─對苯二酚規格 |
![]() |
|
|
CNS 13403
2017 Edition Method of Ultrasonic Test for Seamless Steel and Electric ReSIstance Welded Steel Pipes and Tubes 無縫及電阻銲鋼管超音波檢測法 |
![]() |
|
|
CNS 11071
2017 Edition EmisSIon-Spectroscopic Analysis for Carbon Steel and Low Alloy Steel 碳鋼及低合金鋼之發光光譜分析法 |
![]() |
|
|
CNS 5508
2017 Edition Rolling Bearings; Bearings with Spherical OutSIde Surface and Extended Inner Ring Width, Steel Pressed Housings for Insert Bearings 嵌入夾緊滾動軸承用壓製外殼 |
![]() |
|
|
CNS 7194
2017 Edition SIngle-start solid (monobloc) gear hobs with tenon drive or axial keyway, modules 1 to 40-Nominal dimensions 具有榫槽或鍵槽之單紋螺紋滾齒刀﹝模數1至40﹞─標稱尺度 |
![]() |
|
|
CNS 12289
2017 Edition Reliability Assured Fixed Metal Film ReSIstors (H,J,K) (Established Failure Rate) 可靠度保證金屬皮膜固定電阻器(特性H,J及K)(故障率設定) |
![]() Translated |
Find out:3811Items | To Page of: First -Previous-Next -Last | [80] [81] [82] [83] [84] [85] [86] |