"F " CNS Standards List |
|
CNS 16143-2
2020 Edition Railway applications − Track − PerFormance requirements for fastening systems − Part 2: Fastening systems for concrete sleepers 鐵路應用－軌道－扣件系統之性能要求－第2部：混凝土軌枕用扣件系統 |
|
|
|
CNS 6903
2020 Edition Cable Terminals For Automobiles (Type LB) 汽車用電線端子（橫接環眼型） |
|
|
|
CNS 11423
2020 Edition Method oF Test for Grain Size of Refractory Mortar 耐火墁料細度試驗法 |
|
|
|
CNS 15804
2020 Edition Oil oF cassia, Chinese type − Determination of trans-cinnamaldehyde content − Gas chromatographic method on capillary columns 肉桂油(中國型)－反桂皮醛含量測定法－毛細管柱氣相層析法 |
|
|
|
CNS 3-16
2020 Edition Engineering Drawing (Geometrical Tolerancing - Principles and Methods oF Verification) 工程製圖（幾何公差–檢測原理與方法） |
|
|
|
CNS 12514-11
2020 Edition Fire-resistance tests − Elements of building construction − Part 11: Specific requirements for the assessment of fire protection to structural steel elements 建築物構造構件耐火試驗法－第11部：鋼結構構件防火被覆評估特定要求 |
|
|
|
CNS 12983
2020 Edition Standard Substances For Volumetric Analysis 容量分析用標準試藥 |
|
|
|
CNS 8233
2020 Edition Tyre Valve Thread For Automobiles 汽車輪胎氣門嘴螺紋 |
|
|
|
CNS 7024
2020 Edition Cable Terminals For Automobiles (Type CA) 汽車用電線端子（塞型陽端子） |
|
|
|
CNS 30128
2020 Edition InFormation technology − Sensor networks − Generic sensor network application interface 資訊技術－感測器網路－ 通用感測器網路應用介面 |
|
|
|
CNS 3325
2020 Edition Standard ClassiFication of Castable Refractories 可鑄耐火物分級標準 |
|
|
|
CNS 15227
2020 Edition Single-use medical examination gloves - Part 1: SpeciFication for gloves made from rubber latex or rubber solution 單次使用之醫用檢驗手套－第１部：以乳膠或橡膠溶液製成之手套規格 |
|
|
|
CNS 9746
2020 Edition Method oF Test for Potential Expansion of Portland Cement Mortars Exposed to Sulfate 卜特蘭水泥墁料暴露於硫酸盬中之潛在膨脹檢驗法 |
|
|
|
CNS 13167
2020 Edition SaFety Standards for Construction of Spindle Shapers 立軸機之構造安全基準 |
|
|
|
CNS 5786
2020 Edition Electric Windshield Washers For Automobiles 汽車擋風玻璃電動噴洗器 |
|
|
|
CNS 4238
2020 Edition Finishes and Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 4797-6
2020 Edition SaFety of toys − Part 6: Organic chemical compounds − Requirements 玩具安全－第6部：有機化合物－要求事項 |
|
|
|
CNS 1887
2020 Edition Potassium Fluoride(Reagent) 六氰鐵（Ⅲ）酸鉀（試藥） |
|
|
|
CNS 4532
2020 Edition Terms Relating to the End (Point) oF Fasteners 結件端部詞彙 |
|
|
|
CNS 13169
2020 Edition SaFety Standards for Construction of Veneer Lathes 單板旋切機之構造安全基準 |
|
|
|
CNS 330
2020 Edition Hand Wheels oF Low Heat Insulation Materials 手輪（以低導熱材料製成） |
|
|
|
CNS 15374
2020 Edition LiqueFied petroleum gases - Determination of dissolved residues (High-temperature gas chromatographic method) 液化石油氣－可溶殘餘物測定法（高溫氣相層析法） |
|
|
|
CNS 14104-4
2020 Edition Prosthetics and orthotics - Limb deFiciencies - Part 3: Method of describing upper limb amputation stumps 義肢學與矯具學－肢體缺陷－第４部：導致截肢原因之描述 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter oF Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 5270-1
2020 Edition Graphical Symbols For Fluid Power Dizgrams-Line and Connection 液壓、氣壓圖形符號–管路及連接 |
|
|
|
CNS 1947
2020 Edition Sodium BisulFate, Fused 化學試藥（融熔硫酸氫鈉） |
|
|
|
CNS 11424
2020 Edition Method oF Test for Setting Time of Refractory Mortar 耐火墁料凝結時間試驗法 |
|
|
|
CNS 16145-2
2020 Edition Ceramic tiles − Grouts and adhesives − Part 2: Test methods For adhesives 陶瓷面磚－填縫劑與接著劑－第2部：接著劑試驗法 |
|
|
|
CNS 3333
2020 Edition Zinc alloy ingots intended For castings 鑄造用鋅合金錠 |
|
|
|
CNS 16142
2020 Edition Balancing oF rotating tools and tool systems 旋轉刀具及刀具系統之平衡調校 |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [80] [81] [82] [83] [84] [85] [86] |
