"9 " CNS Standards List |
|
CNS 14319-7
2018 Edition Information technology－Open Document Architecture(ODA)and interchange format － Part 7：Raster graphics content architectures 資訊技術－開放文件架構與交換格式－第7部：光柵圖形內容架構 |
|
|
|
CNS 13798-2
2018 Edition Banking-Personal Identification Number Management and Security-Part 2:Approved Algorithm(s) for PIN Encipherment 銀行業–個人識別碼管理與安全（第二部：認可的個人識別碼加密演算法） |
|
|
|
CNS 14393-3
2018 Edition Biological evaluation of medical devices – Part 3：Tests for genotoxicity, carcinogenicity and reproductive toxicity 醫療器材生物性評估－第三部分：基因毒性、致癌性與生殖毒性之試驗 |
|
|
|
CNS 17966
2018 Edition Assistive products for personal hygiene that support users − Requirements and test methods 支撐使用者之個人衛生輔具－要求及試驗法 |
|
|
|
CNS 12971-3
2018 Edition Identificationcards-Integrated circuit(s) cards with contacts part3:Electronic signals and transmissionprotocols 識別卡（接觸式IC卡）第3部：電子信號及傳輸協定 |
|
|
|
CNS 13692
2018 Edition Support of Packet Mode Terminal Equipment by an Integrated Services Digital Network (ISDN) 整體服務數位網路所提供之分封式終端設備 |
|
|
|
CNS 13789-5
2018 Edition Information technology ─ Security technigues ─ Entity authentication ─Part 5: Mechanisms using zero knowledge techniques 資訊技術─安全技術─實體鑑別機制—第5部：使用零資訊技術機制 |
|
|
|
CNS 9486
2018 Edition Marine Forged Steel Screw Escape Valves (30 kgf/㎠) 船用鍛鋼螺接型安全閥（30 kgf/㎠） |
|
|
|
CNS 9330
2018 Edition Safety signs − General specification 安全標誌－一般性事項 |
|
|
|
CNS 13369-3
2018 Edition Office Machines - Minimum Information to be Included in Specification Sheets Part 3: Postal Franking Machines 事務機器–規格書應包含的最少資訊 第３部: 郵資蓋印機 |
|
|
|
CNS 15091-24
2018 Edition Method of test for deep sea water - Determination of strontium 深層海水檢驗法－鍶之測定 |
|
|
|
CNS 9158
2018 Edition 250V Twin-Core,Three-Core EPR Insulated,CP Sheathed Metal Netting Covered Cable and 250V Twin-Core,Three-Core EPR Insulated Metal Netting Covered PVC Anti-Corrosion Cable for Marine Use 船用２５０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝電纜（附各心線個別遮蔽）及２５０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝ＰＶＣ防蝕電纜（附各心線個別遮蔽） |
|
|
|
CNS 13918
2018 Edition Basic parameters for the measurement of error performance at bit rates below the primary rate 位元速率低於原級速率之錯誤性能測量基本參數 |
|
|
|
CNS 2963
2018 Edition Method of Test for the Life of Electric Heating Wire and Ribbon 電熱線與電熱帶壽命試驗方法 |
|
|
|
CNS 17190-4
2018 Edition Urine-absorbing aids for incontinence − Test methods for characterizing polymer-based absorbent materials − Part 4: Determination of moisture content by mass loss upon heating 尿失禁用尿液吸收輔具－聚合物吸收材料特性試驗法－第4部：以加熱質量損失法測定含水量 |
|
|
|
CNS 9698
2018 Edition Jumper Couplers 電氣連結器 |
|
|
|
CNS 2379
2018 Edition Dried Bonito and Mackerel 鰹鯖鰺類柴魚 |
|
|
|
CNS 12993
2018 Edition Packaging - Complete, filled transport packages and unit loads - Vibration tests at fixed low frequency 包裝貨物與單位裝載之固定低頻率振動試驗法 |
|
|
|
CNS 13797
2018 Edition General Aspects and Principles Relating to Recommendations on ISDN User-Network Interfaces 整體服務數位網路用戶與網路間介面概觀與原則 |
|
|
|
CNS 11994
2018 Edition Cable Clamping Devices for Motor Starters and Controllers in Ships 船用電動機起動器及控制器之電纜固定方法 |
|
|
|
CNS 4393
2018 Edition Plastics - Symbols and abbreviated terms - Part 4：Flame retardants 塑膠－熱塑性塑膠－衛氏軟化 溫度測定法 |
|
|
|
CNS 13936-6
2018 Edition Financial transaction cards-Security architecture of financial transaction systems using integrated circuit cards-Part 6:Cardholder Verification 金融交易卡–使用ＩＣ卡的金融交易系統下的安全架構；第６部：持卡者驗證 |
|
|
|
CNS 12396
2018 Edition Signal Quality at Interface Between Data Terminal Equipment and Synchronous Data Circuit-Terminating Equipment for Serial Data Transmission 串列資料傳輸用資料終端設備與同步資料電路終端設備間介面上之信號品質 |
|
|
|
CNS 14964-15
2018 Edition Wheelchairs - Part 15 : Requirements for information disclosure, documentation and labelling 輪椅－第１５部：資訊宣告、文件與標示之要求 |
|
|
|
CNS 14914
2018 Edition Guidelines for TAGUCHI methods and their application 田口式品質工程與其應用指導綱要 |
|
|
|
CNS 13901
2018 Edition The control of jitter and wander within digital networks which are based on the synchronous digital hierarchy (SDH) 基於同步數位階層的數位網路中之抖動及漂移控制 |
|
|
|
CNS 13913-4
2018 Edition Information technology-Open systems interconnection-Virtual terminal basic class-Register of control object type definitions-Part 4:FVT 217-horizontal tabulation control object 資訊技術–開放系統互連–虛擬終端機基本類別–控制物件型式定義之註冊–第４部：水平定位點控制物件 |
|
|
|
CNS 12798
2018 Edition Basic Mode Control Procedures-Complements 基本模態控制程序–補充事項 |
|
|
|
CNS 14962
2018 Edition Gas cylinders - Valve protection caps and valve guard for industrial and medical gas cylinders - Design, construction and tests 氣體鋼瓶－工業與醫療氣體鋼瓶之閥保護帽與閥保護套－設計、結構與試驗 |
|
|
|
CNS 11199
2018 Edition Pneumatic tyres terms and definitions 鐵路車輛用氣壓式車窗雨刷器 |
|
| Find out:5209Items | To Page of: First -Previous-Next -Last | [79] [80] [81] [82] [83] [84] [85] |
