"A " CNS Standards List| Electromagnetic compatibility | Method Test | Electrical apparatus | Method determination | Machining Allowance | Wooden walking | Micro Hardness | Test conditions | |
|
CNS 833
2022 Edition Ductile CAst Iron Flanged Pipes for Pressure Main Lines 壓力管路用延性鑄鐵管件–凸緣管 |
|
|
|
CNS 14250
2022 Edition Method of test for effect of heAt and air on a moving film of asphalts (rolling thin-film oven test) 柏油流動膜之熱及空氣效應試驗法(滾動薄膜烘箱法) |
|
|
|
CNS 7947
2022 Edition Rolling BeArings General Plans of Boundary Dimensions 滾動軸承界限尺度之一般設計 |
|
|
|
CNS 4797-2
2022 Edition SAfety of toys − Part 2: Migration of certain elements 玩具安全－第2部：特定元素遷移 |
|
|
|
CNS 14065
2022 Edition GenerAl principles and requirements for bodies validating and verifying enviromental information 環境資訊確證與查證機構之一般原則及要求事項 |
|
|
|
CNS 12260
2022 Edition Method of test for oxidAtion characteristics of extreme-pressure lubricating oils 極壓潤滑油抗氧化性能試驗法 |
|
|
|
CNS 16120-1
2022 Edition Video surveillAnce system security − Part 1: General requirements 影像監控系統安全－第1部：一般要求事項 |
|
|
|
CNS 15080
2022 Edition MAximum volatile organic compound content limit value for architectural coatings 建築用塗料之揮發性有機化合物(VOC)最大限量值 |
|
|
|
CNS 6684
2022 Edition Aminoplastic moulding materials – Detrmination of volatile matter 胺基塑膠料揮發物之測定法 |
|
|
|
CNS 10530
2022 Edition Involute Splines -- Dimensions And Measurements (Module 3) 漸開線栓槽組–標稱尺度，測定尺度（模數３） |
|
|
|
CNS 15010
2022 Edition UnplAsticized high impact polyvinyl chloride (PVC-U) pipe fittings for general uses and water supply 一般用與自來水用耐衝擊硬質聚氯乙烯塑膠管件 |
|
|
|
CNS 8144
2022 Edition Solvent-bAse masonry paint 溶劑型水泥漆 |
|
|
|
CNS 14661
2022 Edition PlAstics − Organic recycling − Compostable plastics 塑膠－有機循環－可堆肥塑膠 |
|
|
|
CNS 14776
2022 Edition Method of test for resistAnce of medical face masks to penetration by synthetic blood (horizontal projection of fixed volume at a known velocity) 醫用面(口)罩抗合成血液穿透性試驗法－以已知速度之固定量水平噴灑 |
|
|
|
CNS 11980
2022 Edition Method of test for coefficient of lineAr variation of refractory mortar 耐火墁料乾燥及加熱線變化率試驗法 |
|
|
|
CNS 14674-3
2022 Edition ElectromAgnetic compatibility (EMC) − Generic standards − Part 3: Emission standard for equipment in residential environments 電磁相容(EMC)－一般標準－第3部：居住環境設備之放射標準 |
|
|
|
CNS 15200-1-7
2022 Edition Method of test for coAtings − Part 1-7: General rule − Determination of film thickness 塗料一般試驗法－第1-7部：通則－膜厚測定 |
|
|
|
CNS 6851
2022 Edition Method of test for sieve Analysis of wet milled and dry milled porcenlain enamel 濕磨及乾磨搪瓷之篩析試驗法 |
|
|
|
CNS 15542
2022 Edition GAs cylinders − Design, construction and testing of refillable composite gas cylinders and tubes − Part 3: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 L with non-load-sharing metallic or non-metallic liners or without liners 氣瓶－可重填複合材料氣瓶與氣筒之設計、構造及測試－第3部︰450 L以下具不分擔負載金屬或非金屬內膽或無內膽之全包覆式纖維強化複合材料氣瓶與氣筒 |
|
|
|
CNS 3272
2022 Edition PolymethylmethAcrylate corrugated sheet 聚甲基丙烯酸甲酯波形板 |
|
|
|
CNS 10056
2022 Edition NominAl Dimension of Wide Belt Sanders 寬帶砂光機之標稱尺寸 |
|
|
|
CNS 10531
2022 Edition Involute Splines -- Dimensions And Measurements (Module 4) 漸開線栓槽組–標稱尺度，測定尺度（模數４） |
|
|
|
CNS 14495
2022 Edition Wood preservAtives 木材防腐劑 |
|
|
|
CNS 10058
2022 Edition NominAl Dimension of Hot Presses 熱壓機之標稱尺寸 |
|
|
|
CNS 3176
2022 Edition Piston Ring for InternAl Combustion Engine (Tentative) 內燃機用活塞環 |
|
|
|
CNS 11286
2022 Edition Method of test for rigid Acrylonitrile-butadiene-styrene (ABS) plastics 硬質丙烯腈－丁二烯－苯乙烯（ＡＢＳ）塑膠成型材料檢驗法 |
|
|
|
CNS 4825
2022 Edition DecorAtive electroplated coatings of silver 裝飾用銀電鍍層 |
|
|
|
CNS 3775
2022 Edition Method of test for flAsh and fire points by Cleveland open cup tester 克氏開口杯閃點及燃點試驗法 |
|
|
|
CNS 11274
2022 Edition Method for cAlculating heat balance of kiln and furnace for lime 石灰燒成用窯爐熱平衡計算法 |
|
|
|
CNS 11728
2022 Edition Fire-retArdant paints for buildings 建築用防火塗料 |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [3] [4] [5] [6] [7] [8] [9] |
