"an " CNS Standards List |
|
CNS 15630
2019 Edition Self-ballasted LED lamps for general lighting services with supply voltages > 50 V − Performance requirements 一般照明用安定器內藏式LED 燈泡(供應電壓大於50 V)－性能要求 |
|
|
|
CNS 14253-2
2019 Edition Personal fall-arrest systems − Part 2: Lanyards and energy absorbers 個人擒墜系統−第2 部：繫索及能量吸收器 |
|
|
|
CNS 6959
2019 Edition Acid and Heat Resisting Bricks for Chemical Industry 化學工業用耐酸耐熱磚 |
|
|
|
CNS 15040
2019 Edition Paints and varnishes - Determination of the volatile organic compound content of low - VOC emulsion paints (in-can VOC) 塗料與清漆－低ＶＯＣ乳膠漆（罐內ＶＯＣ）揮發性有機化合物含量之測定 |
|
|
|
CNS 14587-1
2019 Edition Electromagnetic compatibility (EMC) Part 1: General-Section 1: Application and interpretation of fundamental definitions and terms 電磁相容性(EMC)--第1部:總則--第1章:術語與基本定義之應用與說明 |
|
|
|
CNS 15614
2019 Edition Information technology − Telecommunications and information exchange between systems − Near Field Communication − Interface and Protocol(NFCIP-1) 資訊技術－系統間電信與資訊交換－近場通訊－介面與協定(NFCIP-1) |
|
|
|
CNS 16107-2
2019 Edition Hollow taper interface with flange contact surface − Part 2: Receivers − Dimensions 具凸緣接觸面之空心錐度界面－第2部：接收器尺度 |
|
|
|
CNS 15280
2019 Edition Standard test method for tension and elongation of elastic fabrics (constant-rate-of-extension type tensile testing machine) 彈性織物張力與伸度試驗法（定速伸長型試驗機） |
|
|
|
CNS 15755-5-7
2019 Edition Conversion tables for units − Part 5-7: Pressure or stress − Kilopascal and millimeter of water 單位換算表－第5-7 部：壓力或應力－千帕斯卡與毫米水柱 |
|
|
|
CNS 15763-4
2019 Edition Footwear − Test methods for outsoles – Part 4: Tensile strength and elongation of outsoles 鞋類－外底試驗法－第4 部：外底之抗拉強度及伸長率 |
|
|
|
CNS 11013
2019 Edition Iron and steel－Methods for determination of silicon content 鐵及鋼－矽定量法 |
|
|
|
CNS 14373
2019 Edition Method of test for cigarettes - Definitions and standard condition of routine analytical cigarette - smoking machine 捲菸檢驗法－吸菸機用語釋義及標準條件 |
|
|
|
CNS 15051
2019 Edition Fat and oil derivatives - Fatty acid methyl esters (FAME) - Determination of ester and linolenic acid methyl ester contents 油脂衍生物（脂肪酸甲酯）－總脂肪酸甲酯及次亞麻油酸甲酯含量測定法 |
|
|
|
CNS 16102
2019 Edition Specification and qualification of welding procedures for metallic material − Qualification based on pre-production welding test 金屬材料銲接程序規範書及其檢定－依〝製造前銲接試驗〞檢定 |
|
|
|
CNS 30
2019 Edition Belt drives − Pulleys − Quality, finish and balance 皮帶傳動－皮帶輪－品質、加工及平衡 |
|
|
|
CNS 13297
2019 Edition Method of test for abrasion resistance of concrete by sandblasting 混凝土製品耐磨性試驗法(噴砂法) |
|
|
|
CNS 4349
2019 Edition Locks and Latches for Doors in Building 房屋用門鎖及閂鎖 |
Translated |
|
|
CNS 14831
2019 Edition Method of test for oxygenates and paraffin , olefin , naphthene , aromatic（O-PONA）hydrocarbon types in low-olefin spark ignition engine fuels by gas chromatography 低烯烴汽油含氧化物、飽和烴、烯烴、環烷烴及芳香烴（O-PONA）測定法（氣相層析法） |
|
|
|
CNS 14432-2
2019 Edition Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions − Method by analysis of evolved carbon dioxide − Part 2: Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test 塑膠材料在控制堆肥條件下最終好氧生物分解度測定法－二氧化碳釋出量分析法－第2部：實驗室規模重量測定法 |
|
|
|
CNS 16109
2019 Edition Test method for current-voltage (I-V) performance measurement of organic photovoltaic (OPV) and dye-sensitized solar cell (DSSC) 有機與染料敏化太陽能電池－ 電流-電壓性能量測試驗法 |
|
|
|
CNS 15755-6-3
2019 Edition Conversion tables for units − Part 6-3: Work − Joule and kilogram-force meter 單位換算表－第6-3 部：功－焦耳與公斤力公尺 |
|
|
|
CNS 12285
2019 Edition Pressurized explosion-proof construction of electric machineries and apparatuses of mines ( replaced by CNS 3376-0 ) 鋼襯預力混凝土管 |
|
|
|
CNS 15660-3
2019 Edition Test conditions for numerically controlled turning machines and turning centres − Part 3: Geometric tests for machines with inverted vertical workholding spindles 數值控制車床及車削中心機之試驗條件－ 第3部：倒立式工件夾持主軸工具機之幾何試驗 |
|
|
|
CNS 11206
2019 Edition Iron and steel─Methods for atomic absorption spectrometric analysis 鐵及鋼─原子吸收光譜分析法 |
|
|
|
CNS 15753
2019 Edition Plastics piping systems for hot and cold water installations − Polypropylene (PP) − Part 7: Guidance for the assessment of conformity 地下排水及排污非壓力塑膠配管系統－聚乙烯(PE) |
|
|
|
CNS 3304
2019 Edition Testing Standard for Performance of Internal Combustion Engines for Marine Use 船用內燃發動機性能檢驗標準 |
|
|
|
CNS 5559
2019 Edition Shape and Mounting Dimensions of Distributor Contact Breakers for Automobiles 汽車用分電盤白金總成之形狀及安裝尺度 |
Translated |
|
|
CNS 9991
2019 Edition Fixed Design and Method of Use for Oil Seals for Automobiles 汽車用油封安裝部位之設計及使用方法 |
|
|
|
CNS 14499
2019 Edition Road vehicles − Test methods for electrical disturbances from electrostatic discharge 道路車輛－ 靜電放電之電擾動試驗法 |
|
|
|
CNS 62623
2019 Edition Desktop and notebook computers − Measurement of energy consumption 桌上型及筆記型電腦－能源消耗量量測 |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [72] [73] [74] [75] [76] [77] [78] |
