"Test " CNS Standards List| Marking Hatchway | Method Test | Ammonium Chloride | Chemical Reagent | Methods test | Basic Environmental | Application integration | Base Tangent | |
|
CNS 971
2018 Edition Method of Test for Canned Food-Determimation for Degree of Vaccum 食品罐頭檢驗法–真空度之測定 |
Translated |
|
|
CNS 16077
2018 Edition Hoists for the transfer of disabled persons − Requirements and Test methods 身心障礙者移位用起吊裝置－要求及試驗法 |
|
|
|
CNS 13481
2018 Edition Method of Test for Autoclaved Lightweight Aerated Concrete Blocks 高壓蒸氣養護輕質氣泡混凝土磚檢驗法 |
|
|
|
CNS 5036
2018 Edition Methods of Test for Crude Fat in Food 食品中粗脂肪之檢驗方法 |
Translated |
|
|
CNS 12725
2018 Edition Method of Test for Determining of Vitamin A Content for Infant Formula 嬰兒配方食品中維生素Ａ含量測定法 |
Translated |
|
|
CNS 13483
2018 Edition Method of Test for Breaking Load and Elongation of Geotextiles (Grab Method) 地工織物抗拉強度及伸長率試驗法（抓式法） |
|
|
|
CNS 14876
2018 Edition Method of Test for edible oils and fats - Determination of oil stability index 食用油脂檢驗法－穩定性指數之測定 |
|
|
|
CNS 14431
2018 Edition Method of Test for performance of oil/grease interceptor 油脂截留器性能試驗法 |
|
|
|
CNS 9430
2018 Edition Method of Test for Beverage: Determination of Total Solids and Moisture 飲料類製品檢驗法（總固形物及水分之測定） |
Translated |
|
|
CNS 12723
2018 Edition Method of Test for Determining of Vitamin E Content for Infant Formula 嬰兒配方食品中維生素Ｅ含量測定法 |
Translated |
|
|
CNS 450
2018 Edition Wood - Sampling methods and general requirements for physical and mechanical Tests 木材之物理與強度試驗之取樣方法與一般要求 |
|
|
|
CNS 970
2018 Edition Method of Test for Canned Food-Sampling 食品罐頭檢驗法–取樣 |
Translated |
|
|
CNS 15657
2018 Edition Method of Test for pour point of petroleum products (automatic air pressure method) 石油產品流動點試驗法 (自動空氣壓力法) |
|
|
|
CNS 13618
2018 Edition Method of Test for Potential Alkali-Silica Reactivity of Aggregates(Chemical Method) 粒料之潛在鹼質與二氧化矽反應性試驗法（化學法） |
|
|
|
CNS 14964-8
2018 Edition Wheelchairs − Part 8: Requirements and Test methods for static, impact, and fatigue strengths 輪椅－第8部：輪椅靜態、衝擊與疲勞強度要求及試驗法 |
|
|
|
CNS 15200-8-3
2018 Edition Methods of Test for paints – Part 8-3: Evaluation of degradation of paint coatings – Designation of degree of rusting 塗料一般試驗法－第8-3部： 塗膜劣化評估－銹蝕等級 |
|
|
|
CNS 973
2018 Edition Method of Test for Canned Food-Inspection for Interior of Can 食品罐頭檢驗法–罐內壁檢查 |
Translated |
|
|
CNS 10033-2
2018 Edition Complete,filled transport packages - General rules for the compilation of performance Test schedules - Part 2: Quantitative data 包裝貨物性能試驗計畫之編擬通則－第２部：量化數據 |
|
|
|
CNS 4339
2018 Edition Method of Test for Determining Water Emersion Endurance of Glue Seams of Paper Sacks 紙袋膠縫耐水浸潤時間之試驗法 |
|
|
|
CNS 4705
2018 Edition Method of Test for Photoelectric Controls for Public Lighting 路燈用光電式自動點滅器檢驗法 |
Translated |
|
|
CNS 12382
2018 Edition Method of Test for the California Bearing Ratio (CBR) 夯實土樣加州載重比試驗法 |
|
|
|
CNS 12387
2018 Edition Method of Test for Classification of Soils for Engineering Purposes 工程用土壤分類試驗法 |
|
|
|
CNS 13300
2018 Edition Method of Test for Tensile Properties of Geotixtiles by the Wide - Width Strip 地工織物抗拉力試驗法（寬幅法） |
|
|
|
CNS 14280
2018 Edition Method of Test for physical performances of building curtain walls - General rule 帷幕牆及其附屬門、窗物理性能試驗總則 |
|
|
|
CNS 15562-5
2018 Edition Stationary training equipment − Part 5: Stationary exercise bicycles and upper body crank training equipment, additional specific safety requirements and Test methods 固定式訓練器材－第5部：固定式健身單車及上半身曲柄訓練器材之附加特定安全要求與試驗法 |
|
|
|
CNS 15200-8-4
2018 Edition Methods of Test for paints – Part 8-4: Evaluation of degradation of paint coatings – Designation of degree of cracking 塗料一般試驗法－第8-4部： 塗膜劣化評估－龜裂等級 |
|
|
|
CNS 13298
2018 Edition Method of Test for Water Permeability of Geotextiles by Permittivity 地工織物正向透水率試驗法 |
|
|
|
CNS 3577
2018 Edition Method of Test for hydrocarbon types in liquid petroleum products by fluorescent indicator adsorption 液體石油產品碳氫類別試驗法(螢光指示劑吸附法) |
|
|
|
CNS 5034
2018 Edition Method of Test for Ash in Food 食品中粗灰分之檢驗方法 |
Translated |
|
|
CNS 15606-3
2018 Edition Plastics − Determination of tensile properties − Part 2: Test conditions for moulding and extrusion plastics 塑膠－抗拉性能測定法－第3部： 膜與片之試驗條件 |
|
| Find out:4507Items | To Page of: First -Previous-Next -Last | [65] [66] [67] [68] [69] [70] [71] |
