"－ " CNS Standards List |
|
CNS 1356
2018 Edition Methed of test for residue ash content of pulps, paper and board on ignition at 525℃ 紙漿、紙及紙板灰分試驗法－５２５℃ |
|
|
|
CNS 3376-5
2018 Edition Electrical apparatus of general use for explosive gas atmospheres-Part 5: Powder filling 〝q〞 爆炸性氣體環境用電機設備－第５部：填粉防爆構造〝ｑ〞 |
|
|
|
CNS 15591-1
2018 Edition Electrical apparatus for use in the presence of combustible dust - Part 1: Protection by enclosures〝tD〞 可燃性粉塵環境用電機設備－第1部：外殼保護〝tD〞 |
|
|
|
CNS 15620-4
2018 Edition Insulation coordination for equipment within low-voltage system – Part 4: Considerationof high-frequency voltage stress 低電壓系統下設備之絕緣協調－第4 部：高頻電壓應力之考量 |
|
|
|
CNS 15703-2
2018 Edition Tool shanks with 7/24 taper for automatic tool changers – Part 2: Dimensions and designation of shanks of forms J, JD and JF 自動換刀器用7/24 錐度刀柄－第2 部：刀柄型式J、JD 及JF 之尺度及標示 |
|
|
|
CNS 14378
2018 Edition Information technology-Telecommunications and information exchange between systems - Use of X.25 to provide the OSIconnection- Mode network service 資訊技術－系統間電信與資訊交換－使用X．25提供OSI連接模式網路服務 |
|
|
|
CNS 61347-1
2018 Edition Lamp controlgear − Part 1: General and safety requirements 光源控制裝置－第1部：通則及安全要求 |
|
|
|
CNS 13382-6
2018 Edition Implants for surgery - Metallic materials - Cobalt-chromium-molybdenum casting alloy 外科體內植入物－金屬材料－鑄造鈷-鉻-鉬合金 |
|
|
|
CNS 15590-7
2018 Edition Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 結件之機械性質－第7部：標稱直徑1 mm至10 mm螺栓與螺釘之扭力試驗及最小扭矩 |
|
|
|
CNS 15660-8
2018 Edition Test conditions for numerically controlled turning machines and turning centres − Part 8: Evaluation of thermal distortions 數值控制車床及車削中心機之試驗條件－第8 部：熱變形之評估 |
|
|
|
CNS 16076
2018 Edition Respiratory protective devices − Full face masks − Requirements, testing, marking 呼吸防護裝置－全面罩－要求、試驗、標示 |
|
|
|
CNS 14545-6
2018 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 2:Glow-wire flammability test on materials 火災危險性試驗－第２部：試驗方法－第１章／第２單元：材料可燃性之熾熱線試驗 |
|
|
|
CNS 15569-3
2018 Edition Hydraulic fluid power - Filter elements - Part 3: Verification of material compatibility with fluids 液壓流體動力－過濾器濾心－第3部：查證材料及流體之相容性 |
|
|
|
CNS 6391
2018 Edition Method of test for meat and meat products - Determination of nitrate content 肉及肉製品檢驗法－硝酸鹽含量之測定 |
|
|
|
CNS 15620-3
2018 Edition Insulation coordination for equipment within low-voltage system – Part 3: Use of coating, potting or moulding for protection against pollution 低電壓系統下設備之絕緣協調－第3 部：用於污染防護之塗裝、封裝或壓塑 |
|
|
|
CNS 15676-3
2018 Edition Interior air of road vehicles − Part 3: Screening method for the determination of the emissions of volatile organic compounds from vehicle interior parts and materials − Micro-scale chamber method 道路車輛內部空氣－第3 部：車輛內部零件與材料之揮發性有機化合物逸散量篩檢測定法－微型試驗箱法 |
|
|
|
CNS 9559
2018 Edition Round-steel link chains for lifting - Grade 5 起重設備用圓鋼製環鏈－品質等級５ |
|
|
|
CNS 15710-3
2018 Edition Effects of current on human beings and livestock – Part 3: Effects of currents passing through the body of livestock 電流在人體及家畜上之效應－第3 部：電流通過家畜軀體之效應 |
|
|
|
CNS 14325
2018 Edition Broadband integrated services digital network (B-ISDN)-Digital subscriber signalling system no.2 (DSS 2)-Additional traffic parameters 寬頻整體服務數位網路－第二號數位用戶信號系統－附加訊務參數 |
|
|
|
CNS 15568
2018 Edition Protecting Equipment and Distribution of Three-Phase 220 V Motors for General Use 電擊防護－裝設及設備之一般觀念 |
|
|
|
CNS 15588-4
2018 Edition Electric traction − Rotating electrical machines for rail and road vehicles − Part 4: Permanent magnet synchronous electrical machines connected to an electronic converter 電力牽引－軌道及道路車輛用之旋轉電機－第4部：電子換流器供電之永磁同步電機 |
|
|
|
CNS 14761
2018 Edition B-ISDN user part - Overview of the B-ISDN network node interfacesignalling capability set 2, step 1 寬頻整體服務數位網路使用者部－寬頻整體服務數位網路之網路節點介面信號能力集2步驟1之概觀 |
|
|
|
CNS 15612
2018 Edition Plastics − Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics − Part 1: Standard method 塑膠－吸水率測定法 |
|
|
|
CNS 4394-2
2018 Edition Plastics − Injection moulding of test specimens of thermoplastic materials − Part 1: General principles, and moulding of multipurpose and bar test specimens 塑膠－熱塑性塑膠射出成型試片－第2部：小型拉伸試驗棒 |
|
|
|
CNS 13382-7
2018 Edition Implants for surgery - Metallic materials - Wrought titanium 6-aluminium 4-vanadium alloy 外科體內植入物－金屬材料－鍛造鈦－６鋁－４釩合金 |
|
|
|
CNS 9560
2018 Edition Round-steel link chains for lifting - Grade 6 起重設備用圓鋼製環鏈－品質等級６ |
|
|
|
CNS 13382-3
2018 Edition Implants for surgery - Metallic materials - Wrought cobalt-nickel-chromium-molybdenum-tungsten-iron alloy 外科體內植入物－金屬材料－鍛造鈷－鎳－鉻－鉬－鎢－鐵合金 |
|
|
|
CNS 11626
2018 Edition Information Processing Systems-Data Communication-High-Level Data Link Control Procedures-Frame Structure 資訊處理系統（資料通信用高階資料鏈控制程序－框結構） |
|
|
|
CNS 10666
2018 Edition Disposable gas-lighter (for cigarette ignition) - Safety requirements 拋棄式打火機－安全要求 |
Translated |
|
|
CNS 14360
2018 Edition Broadband integrated services digital network (B-ISDN)-Functional description of the B-ISDN user part (B-ISUP) of signalling system no.7 寬頻整體服務數位網路－第七號信號系統寬頻整體服務數位網路使用者部之功能描述 |
|
| Find out:3729Items | To Page of: First -Previous-Next -Last | [65] [66] [67] [68] [69] [70] [71] |
