"－ " CNS Standards List |
|
CNS 1137
2018 Edition Pliers and nippers - Nomenclature 夾鉗與剪鉗－握式夾鉗（尖嘴鉗） |
|
|
|
CNS 14545-6
2018 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 2:Glow-wire flammability test on materials 火災危險性試驗－第２部：試驗方法－第１章／第２單元：材料可燃性之熾熱線試驗 |
|
|
|
CNS 6610
2018 Edition Method of test for meat and meat products - Determination of soybean flour and soy protein concentrate content 肉及肉製品檢驗法－黃豆粉和濃縮黃豆蛋白含量之測定 |
|
|
|
CNS 7046-5
2018 Edition Plastics piping systems for hot and cold water installations − Polybutene (PB) − Part 3: Fittings 冷熱水裝置用塑膠管配管系統－聚丁烯(PB)－第5部：系統適合度 |
|
|
|
CNS 13283-9
2018 Edition Electronic data interchange for administration,commerce and transport (EDIFACT)-Application level syntax rules(Syntax version number:4)-Part9:Security key and certificate management message (Message type-KEYMAN) 行政管理、商務與運輸用電子資料交換（ＥＤＩＦＡＣＴ）－應用層語法規則（第４版語法）－第９部：安全金鑰與憑證管理訊息（訊息型式－ＫＥＹＭＡＮ） |
|
|
|
CNS 15593-42
2018 Edition Electricity metering – Data exchange for meter reading, tariff and load control – Part 42: Physical layer services and procedures for connection-oriented asynchronous data exchange 電力計量－讀表、計費及負載控制之資料 交換－第42部：連接導向非同步資料 交換之實體層服務及程序 |
|
|
|
CNS 62282-3-300
2018 Edition Fuel cell technologies – Part 3-300: Stationary fuel cell power systems – Installation 燃料電池技術－第3-300部：定置型燃料電池發電系統－設置 |
|
|
|
CNS 15569-3
2018 Edition Hydraulic fluid power - Filter elements - Part 3: Verification of material compatibility with fluids 液壓流體動力－過濾器濾心－第3部：查證材料及流體之相容性 |
|
|
|
CNS 15568
2018 Edition Protecting Equipment and Distribution of Three-Phase 220 V Motors for General Use 電擊防護－裝設及設備之一般觀念 |
|
|
|
CNS 15130-3-25
2018 Edition Tests on electric cables under fire conditions - Part 3-25 : Test for vertical flame spread of vertically-mounted bunched wires or cables - Category D 電纜之燃燒試驗－第３－２５部：垂直敷設成束電線電纜之垂直火焰擴散試驗－類別Ｄ |
|
|
|
CNS 15590-7
2018 Edition Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 結件之機械性質－第7部：標稱直徑1 mm至10 mm螺栓與螺釘之扭力試驗及最小扭矩 |
|
|
|
CNS 15612
2018 Edition Plastics − Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics − Part 1: Standard method 塑膠－吸水率測定法 |
|
|
|
CNS 14698
2018 Edition Infrastructure of audiovisual services - Transmission multiplexing and synchronization - Multiplexing protocol for low bit rate multimedia communication 視聽服務之基本結構－傳輸多工及同步－低位元速率多媒體通信之多工協定 |
|
|
|
CNS 11626
2018 Edition Information Processing Systems-Data Communication-High-Level Data Link Control Procedures-Frame Structure 資訊處理系統（資料通信用高階資料鏈控制程序－框結構） |
|
|
|
CNS 4394-2
2018 Edition Plastics − Injection moulding of test specimens of thermoplastic materials − Part 1: General principles, and moulding of multipurpose and bar test specimens 塑膠－熱塑性塑膠射出成型試片－第2部：小型拉伸試驗棒 |
|
|
|
CNS 13382-6
2018 Edition Implants for surgery - Metallic materials - Cobalt-chromium-molybdenum casting alloy 外科體內植入物－金屬材料－鑄造鈷-鉻-鉬合金 |
|
|
|
CNS 6391
2018 Edition Method of test for meat and meat products - Determination of nitrate content 肉及肉製品檢驗法－硝酸鹽含量之測定 |
|
|
|
CNS 14761
2018 Edition B-ISDN user part - Overview of the B-ISDN network node interfacesignalling capability set 2, step 1 寬頻整體服務數位網路使用者部－寬頻整體服務數位網路之網路節點介面信號能力集2步驟1之概觀 |
|
|
|
CNS 15588-4
2018 Edition Electric traction − Rotating electrical machines for rail and road vehicles − Part 4: Permanent magnet synchronous electrical machines connected to an electronic converter 電力牽引－軌道及道路車輛用之旋轉電機－第4部：電子換流器供電之永磁同步電機 |
|
|
|
CNS 14238
2018 Edition Quality management systems - Guidelines for configuration management 品質管理系統－形態管理指導綱要 |
|
|
|
CNS 61347-1
2018 Edition Lamp controlgear − Part 1: General and safety requirements 光源控制裝置－第1部：通則及安全要求 |
|
|
|
CNS 15703-2
2018 Edition Tool shanks with 7/24 taper for automatic tool changers – Part 2: Dimensions and designation of shanks of forms J, JD and JF 自動換刀器用7/24 錐度刀柄－第2 部：刀柄型式J、JD 及JF 之尺度及標示 |
|
|
|
CNS 10666
2018 Edition Disposable gas-lighter (for cigarette ignition) - Safety requirements 拋棄式打火機－安全要求 |
Translated |
|
|
CNS 9331
2018 Edition Safety colours − General specification 安全顏色－一般性事項 |
|
|
|
CNS 15832-2-4
2018 Edition Method of test for coating components − Part 2-4: Component analysis in solvent soluble matter − Alkyd resin 塗料成分試驗法－第2-4部：溶劑可溶物中成分分析－醇酸樹脂 |
|
|
|
CNS 15678-2
2018 Edition Tail lifts − Platform lifts for mounting on wheeled vehicles − Safety requirements − Part 2: Tail lifts for passengers 車尾升降機－裝置於車輛之平台升降機－安全要求－第2 部︰客用車尾升降機 |
|
|
|
CNS 15710-3
2018 Edition Effects of current on human beings and livestock – Part 3: Effects of currents passing through the body of livestock 電流在人體及家畜上之效應－第3 部：電流通過家畜軀體之效應 |
|
|
|
CNS 14763
2018 Edition Extensions to the B-ISDN user part－Modification procedures for sustainable cell rate parameters 寬頻整體服務數位網路使用者部之延伸－可維持的細胞速率參數之修改程序 |
|
|
|
CNS 14360
2018 Edition Broadband integrated services digital network (B-ISDN)-Functional description of the B-ISDN user part (B-ISUP) of signalling system no.7 寬頻整體服務數位網路－第七號信號系統寬頻整體服務數位網路使用者部之功能描述 |
|
|
|
CNS 14325
2018 Edition Broadband integrated services digital network (B-ISDN)-Digital subscriber signalling system no.2 (DSS 2)-Additional traffic parameters 寬頻整體服務數位網路－第二號數位用戶信號系統－附加訊務參數 |
|
| Find out:3729Items | To Page of: First -Previous-Next -Last | [65] [66] [67] [68] [69] [70] [71] |
