"Test " CNS Standards List| C11 Type | Method test | Laminated Springs | Method test | Morse Taper | Calculation Load | Cargo Lights | Method test | |
|
CNS 10980-1
2019 Edition Lead-acid traction batteries - general requirements and methods of Test 電動車用鉛蓄電池-一般要求及檢驗法 |
|
|
|
CNS 15660-2
2019 Edition Test conditions for numerically controlled turning machines and turning centres − Part 2: Geometric tests for machines with a vertical workholding spindle 數值控制車床及車削中心機之試驗條件－ 第2部：立式工件夾持主軸工具機之幾何試驗 |
|
|
|
CNS 13905
2019 Edition Methods of Test for water absorbency of textiles 纖維製品吸水性試驗法 |
|
|
|
CNS 7265
2019 Edition Ropes - Sampling and Conditioning for Testing 繩子之取樣與試樣條件 |
|
|
|
CNS 8242
2019 Edition Method of Warm-up Test of Carburetors for Automobiles 汽車用化油器溫車運轉性能試驗法 |
|
|
|
CNS 2770-18
2019 Edition Method of Test for Feeds : Determination 飼料檢驗法（鉻之測定） |
|
|
|
CNS 8808
2019 Edition Method of Test for minimum turning radius for automobiles 汽車最小迴轉半徑試驗法 |
|
|
|
CNS 11991
2019 Edition Method of Test for joint treatment materials for gypsum boards 石膏板用接縫處理材料檢驗法 |
|
|
|
CNS 12179
2019 Edition Method of Test of Porosity for Brake Linings and Pads of Automobiles 汽車用煞車軔襯及圓盤煞車襯墊之氣孔率試驗法 |
|
|
|
CNS 9200
2019 Edition Method of Corrective Test for Etched - Stem Mercury - in - Glass Thermometer (Partial Immersion Type) 刻浸沒線玻璃水銀溫度計補正試驗法 |
|
|
|
CNS 8730
2019 Edition Method of Test for Sulfanitran in Feed 飼料中磺胺乃安之測定 |
|
|
|
CNS 15207-7
2019 Edition Road vehicles - Component Test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 7: Direct radio frequency (RF) power injection 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第７部：直接射頻功率注入 |
|
|
|
CNS 15207-5
2019 Edition Road vehicles - Component Test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 5: Stripline 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第５部：帶線 |
|
|
|
CNS 15094-1
2019 Edition Fine ceramics - Test method for air purification performance of photocatalytic materials - Part 1: Removal of nitric oxide 精密陶瓷－光觸媒材料之空氣淨化性能測定法－第1部：氮氧化物去除性能 |
|
|
|
CNS 1239
2019 Edition Method of Test for Fundamental Transverse Longitudinal and Torsional Frequencies of Concrete Specimens 混凝土試體橫向、縱向及扭曲之基本頻率試驗法 |
Translated |
|
|
CNS 6812
2019 Edition Method of Test for Hot Water Heaters of Automobiles 汽車用熱水式暖氣機檢驗法 |
|
|
|
CNS 15762-12
2019 Edition Footwear − Test methods for uppers – Part 12: Seam strength of uppers, linings and insocks 鞋類－鞋面試驗法－第12 部：鞋面、內裡及鞋墊之縫合強度 |
|
|
|
CNS 7376
2019 Edition Method of plane bending fatigue Testing of metal plates 金屬板之平面彎曲疲勞試驗法 |
|
|
|
CNS 12514-9
2019 Edition Fire-resistance Tests – Elements of building construction – Part 9: Specific requirements for non-loadbearing ceiling elements 建築物構造構件耐火試驗法－第9 部：非承重天花板特定要求 |
|
|
|
CNS 10090
2019 Edition Method of Test for penetration of bitumen/asphalt 瀝青/柏油針入度試驗法 |
|
|
|
CNS 6170
2019 Edition Method of Test for DC Generators of Automobiles 汽車用直流發電機試驗法 |
|
|
|
CNS 15200-3-6
2019 Edition Method of Test for coatings − Part 3-6: Film formability of coatings − Print-free test 塗料一般試驗法－第3-6部：塗膜成形性－不黏著乾燥性 |
|
|
|
CNS 12626
2019 Edition Method of Test for Electronic Taximeter 電子式汽車計費表檢驗法 |
Translated |
|
|
CNS 15766-1
2019 Edition Test on gases evolved during combustion of materials from cables – Part 1: Determination of the halogen acid gas content 電(光)纜材料燃燒時釋出氣體之試驗－第1 部：氫鹵酸氣含量之測定 |
|
|
|
CNS 357
2019 Edition Bicycle chains – Characteristics and Test methods 自行車鏈條－特徵與試驗方法 |
|
|
|
CNS 14821
2019 Edition Method of Test for nonwoven fabrics of medical use 醫療用非織物試驗法 |
|
|
|
CNS 14545-5
2019 Edition Fire hazard Testing-Part 2:Test methods-Section 1/sheet 1:Glow-wire end-product test and guidance 火災危險性試驗－第２部：試驗方法－第１章／第１單元：完成品之熾熱線試驗及指引 |
|
|
|
CNS 15462
2019 Edition Method of Test for flow consistency of controlled low strength material (CLSM) 控制性低強度材料流動稠度試驗法 |
|
|
|
CNS 13181-8
2019 Edition The Method of Test of Vibration Testing Procedures for LGP Automobile Fuel Systems 液化石油氣汽車燃氣系統–振動測試程序 |
Translated |
|
|
CNS 16097-2
2019 Edition Machine tools − Dimensions and geometric Tests for self-centring chucks with two-piece jaws − Part 2: Power-operated chucks with tongue and groove type jaws 工具機－具兩件式夾爪之自定心夾頭的尺度及幾何試驗－第2部：具榫槽式夾爪之動力操作夾頭 |
|
| Find out:4507Items | To Page of: First -Previous-Next -Last | [58] [59] [60] [61] [62] [63] [64] |
