CNS Standards Solution | HOME | LOGIN | SIGN UP | CONTACT US | 中文版 |
�� ��

Chinese National Standards
中華民國國家標準
- Taiwan 台灣 -
 

"T " CNS Standards List

C-Electrical Engineering
CNS 9095    2021 Edition
Discharge Coil for High VolTage Power Capacitor
高壓電力電容器放電線圈
S-Domestic Wares
CNS 11464    2021 Edition
GymnasTic equipment - Horizontal bars
體操設備-單槓
B-Mechanical Engineering
CNS 2695    2021 Edition
WaTer-cooled Diesel Engines for Land Use (Small Size)
陸用小型水冷柴油發動機

Translated
A-Civil Engineering & Architecture
CNS 4062    2021 Edition
MeThod of Test for Reinforced Concrete Ditches (U Type)
鋼筋混凝土U形溝檢驗法

Translated
Z8-General & Miscellaneous
CNS 12805    2021 Edition
MeThod of break test for fillet welded joint
填角銲接接頭之斷裂試驗法
K-Chemical Industry
CNS 12145    2021 Edition
Varnish for inTerior wooden floor
室內用木質地板清漆
C-Electrical Engineering
CNS 7214    2021 Edition
Test methods for magnetic steel sheet and strip
電磁鋼片及鋼帶試驗法
L-Textile Industry
CNS 2337    2021 Edition
Glossary of Terms Used for Fibers (Yarns)
纖維詞彙(紗線部份)
L-Textile Industry
CNS 11310    2021 Edition
MeThod of Test for Soil Redeposition, Resistance to Launder-Ometer
織物抗再污染性檢驗法(Launder–Ometer法)
O-Wood Industry
CNS 3219    2021 Edition
PresenTation of Title Information of Series
加壓注入防腐處理竹材
N-Agriculture, Food
CNS 3653    2021 Edition
MeThod of test for edible oils and fats-AOM method for stability test
食用油脂檢驗法-穩定性試驗(,活性氧化法)
K-Chemical Industry
CNS 261    2021 Edition
MoTor vehicle brake fluid
車用煞車油
S-Domestic Wares
CNS 15442    2021 Edition
WriTing and marking instruments − Specification for caps to reduce the risk of asphyxiation
書寫及標記文具-降低帽蓋窒息風險之規範
B-Mechanical Engineering
CNS 3255    2021 Edition
Power Rice Transplanters
高壓動力噴霧機

Translated
Z8-General & Miscellaneous
CNS 2113-2    2021 Edition
Brinell hardness Test − Part 2: Table of hardness values
勃氏硬度試驗法-第2部:硬度值表
B-Mechanical Engineering
CNS 9346    2021 Edition
Wheel SupporTs for Hand Platform Truck
手推平車用輪架
K-Chemical Industry
CNS 3295    2021 Edition
PolycarbonaTe Sheets
聚氯丁二烯橡膠接著劑

Translated
C-Electrical Engineering
CNS 9829    2021 Edition
SecuriTy Current of Conduct Distribution
導線管槽配線安全電流
B-Mechanical Engineering
CNS 9973    2021 Edition
WaTer Gages for Boilers-with Cocks Tubular Type
鍋爐水位計–附10 kgf/㎠旋塞圓管型
Z5-Physical Distribution & Packaging
CNS 10676    2021 Edition
HeaT shrinkable plastic films for packaging
熱收縮包裝用塑膠薄膜
C-Electrical Engineering
CNS 12354    2021 Edition
ConTrast of Wire Gauge to Diameter and Section Area
線規與公制直徑及有效截面積對照表
K-Chemical Industry
CNS 3293    2021 Edition
Polyvinyl chloride raincoaTs
軟質聚氯乙烯夾網塑膠皮

Translated
A-Civil Engineering & Architecture
CNS 5264    2021 Edition
MeThod of Test for Amount of Materials in Soils Finer Than the Test Sieve 75}zYm CNS 386
土壤內顆粒小於試驗篩75 mCNS386含量試驗法
B-Mechanical Engineering
CNS 716    2021 Edition
GaTe Valve (Flange Type) (Nominal Pressure 16 kgf/㎠ )
截流活門(凸緣式)(標稱壓力16公斤/平方公分;最大使用壓力16公斤/平方公分)
B-Mechanical Engineering
CNS 7869    2021 Edition
Air FilTer Units for Ventilation
通風用過濾器
C-Electrical Engineering
CNS 8364    2021 Edition
Mica wiTh Paper on One Side ( Sheets and Types )
單面紙雲母片及帶
B-Mechanical Engineering
CNS 7563    2021 Edition
FlaT Round Head Rivets Nominal Diameters 1.4 to 6 mm
扁圓頭鉚釘(標稱直徑1.4至6mm)
L-Textile Industry
CNS 11552    2021 Edition
DefiniTion of Side (Left or Right) of Doubling Machines, Twisting Machines and Winding Machines
併紗機、撚線機及絡紗機左右側的決定方法
C-Electrical Engineering
CNS 1143    2021 Edition
InsulaTing Rubber Tape
絕緣橡膠布帶

Translated
C-Electrical Engineering
CNS 6044    2021 Edition
Press Work Mica PlaTes
電機用壓紙板

Find out:15111Items   |  To Page of: First -Previous-Next -Last  | [55] [56] [57] [58] [59] [60] [61]

 

| HOME | LOGIN | SIGN UP | CONTACT US | 中文版 | ©  CNS-standards.org Copyright  2001-2025 All Rights Reserved
The authority agency link :
Bureau of Standards, Metrology & Inspection M.O.E.A.
This site is not affiliated with or endorsed by the BSMI or MOEA.