"M " CNS Standards List |
|
CNS 15498
2021 Edition Methods of measurement on light emitting diode modules for thermal resistance 發光二極體模組之熱阻量測法 |
|
|
|
CNS 12695
2021 Edition Method of Test for Chain Door Fasteners 門鏈檢驗法 |
Translated |
|
|
CNS 13802-5
2021 Edition Graphical SyMbols for Diagrams (Semiconductors and Electron Tubes) 電機工程製圖符號（半導體及電子管） |
|
|
|
CNS 15932-1
2021 Edition Rubber, vulcanized or therMoplastic − Part 1: Determination of adhesion to textile fabrics 硫化或熱塑性橡膠接著強度試驗－第1 部：與織物接著測定法 |
|
|
|
CNS 8363
2021 Edition Mica with Paper on Both Sides ( Sheets and Types ) 雙面紙雲母片及帶 |
|
|
|
CNS 4399
2021 Edition Method of test for forzen snail meat 冷凍蝸牛肉檢驗法 |
Translated |
|
|
CNS 4726
2021 Edition PerforMance Test of Hinges 鉸鏈往復開關檢驗法 |
|
|
|
CNS 3621
2021 Edition General Rules for Cores Made of Ferromagnetic Oxides 陶磁鐵心通則 |
|
|
|
CNS 13349
2021 Edition Method of test for grease resistance of paper and board – Permeability test 紙及紙板抗油脂性試驗法（滲透法） |
|
|
|
CNS 3043
2021 Edition Glass Mats for Storage Batteries 蓄電池用玻璃纖維墊片 |
|
|
|
CNS 14905-18
2021 Edition Hand-held Motor-operated electric tools - Safety - Part 2-18: Particular requirements for strapping tools 手持型電動工具－安全性－第２－１８部：打包機之個別規定 |
|
|
|
CNS 3644
2021 Edition Method of test for edible oils and fats－Determination of relative gravity 食用油脂檢驗法－比重之測定 |
|
|
|
CNS 13718
2021 Edition Method for measurement of amount of hydrogen evolved from steel welds 鋼材銲道氫含量量測法 |
|
|
|
CNS 5090
2021 Edition Method of Test for Specific Gravity of Soils 土壤比重試驗法 |
|
|
|
CNS 60335-2-4
2021 Edition Household and siMilar electrical appliances − Safety − Part 2-4: Particular requirements for spin extractors 家用和類似用途電器－安全性－第2-4 部：旋轉式脫水機之個別規定 |
|
|
|
CNS 15432
2021 Edition Methods of measurement of the magnetic properties of magnetic steel sheet and strip by means of a single sheet tester 電磁鋼片單片電磁特性試驗法 |
|
|
|
CNS 15923
2021 Edition TherMoplastics pipes − Determination of ring stiffness 熱塑性塑膠管－環剛度測定 |
|
|
|
CNS 15885
2021 Edition Cycles − Pedal axle and crank asseMbly with square end fitting − Assembly dimensions 自行車－以方端固定之踏板軸與曲柄總成－總成尺度 |
|
|
|
CNS 13802-11
2021 Edition Graphical syMbols for diagrams (Architectural and topographical installation plans and diagrams) 電機工程製圖符號（建築及地形學之裝置圖與製圖） |
|
|
|
CNS 5310
2021 Edition Switch Board LaMps 配電盤用燈泡 |
Translated |
|
|
CNS 6550
2021 Edition Locate Rings of Molds for Plastics 塑膠型模用定位環 |
|
|
|
CNS 62053-21
2021 Edition Electricity Metering equipment − Particular requirements − Part 21：Static meters for AC active energy (classes 0.5, 1 and 2) 電計量設備－特定要求－第21部：交流有效電能用電子式瓦時計(0.5級、1級及2級) |
|
|
|
CNS 9208
2021 Edition Method of test for air-entraining admixtures for concrete 混凝土用輸氣劑檢驗法 |
|
|
|
CNS 5616
2021 Edition Method of Testing for Recovery From Creasing of Fabrics 織物皺摺回復度檢驗法 |
|
|
|
CNS 8150
2021 Edition Methods of Test for Seam Strength of Clothes 紡織品縫合強力檢驗法 |
|
|
|
CNS 8133
2021 Edition Oil of citronella, Sri Lankan type [CyMbopogon nardus (L.) W. Watson var. lenabatu Stapf.] 斯里蘭卡香茅油 |
|
|
|
CNS 3142-2
2021 Edition Plastics − Unplasticized poly (vinyl chloride) sheets − Part 1: Types, diMensions and characteristics for sheets of thickness not less than 1 mm 塑膠－硬質聚氯乙烯板片－第2部：厚度小於1 mm薄片之種類、尺度及特性 |
|
|
|
CNS 15477
2021 Edition Method of test for moisture or volatile distillates in bituminous paving mixtures 瀝青鋪面混合料中水分或揮發性蒸餾液試驗法 |
|
|
|
CNS 14680
2021 Edition Method of test for Carbadox, Nitrofurazone and Furazolidone in feeds 飼料中卡巴得、硝基呋喃及富來頓檢驗方法 |
|
|
|
CNS 4838
2021 Edition Salted cucuMbers 鹽漬胡瓜 |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [55] [56] [57] [58] [59] [60] [61] |
