"3, " CNS Standards List |
|
CNS 13306-1-4
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Ancillary equipment - Radiated disturbances 射頻擾動和免疫力量測設備與量測方法－第１－４部：射頻擾動和免疫力量測設備－輔助設備－輻射擾動 |
|
|
|
CNS 15130-2-2
2019 Edition Tests on electric and optical fibre cables under fire conditions − Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable – Procedure for diffusion flame 電纜及光纜之燃燒試驗－ 第2-2部:單條小型絕緣電線或電纜之垂直火焰延燃試驗－ 擴散火焰之程序 |
|
|
|
CNS 15593-62
2019 Edition Electricity metering – Data exchange for meter reading, tariff and load control – Part 62: Interface classes 電力計量－讀表、計費及負載控制之資料交換－第62 部：介面類別 |
|
|
|
CNS 12536
2019 Edition Methods of Chemical Analysis for Tungsten Powder and Tungsten Carbide Powder 鎢粉及碳化鎢粉化學分析法 |
|
|
|
CNS 11391
2019 Edition Decorative electroplated coatings of copper/nickel/chromium on plastics 塑膠裝飾用之銅鎳鉻電鍍層 |
|
|
|
CNS 12285
2019 Edition Pressurized explosion-proof construction of electric machineries and apparatuses of mines ( replaced by CNS 3376-0 ) 鋼襯預力混凝土管 |
|
|
|
CNS 3913
2019 Edition Method of Test for Search Lights of Marine Use 船用探照燈檢驗法 |
Translated |
|
|
CNS 15203
2019 Edition Oils of bergamot, lemon, citron and lime, fully or partially reduced in bergapten - Determination of bergapten content by high-pressure liquid chromatography (HPLC) 香檸檬油、檸檬油、柑橘油及萊姆油－香檸檬烯含量測定高效能液相層析法（ＨＰＬＣ） |
|
|
|
CNS 16103
2019 Edition Protective clothing − Protection against chemicals − Determination of resistance of protective clothing materials to permeation by liquids and gases 化學防護服 |
|
|
|
CNS 3666
2019 Edition Method of Magnetic Particle Flaw Detection Test for Ferromagnetic Materials 鋼鐵材料之磁粉探傷法 |
|
|
|
CNS 14432-2
2019 Edition Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions − Method by analysis of evolved carbon dioxide − Part 2: Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test 塑膠材料在控制堆肥條件下最終好氧生物分解度測定法－二氧化碳釋出量分析法－第2部：實驗室規模重量測定法 |
|
|
|
CNS 20349-1
2019 Edition Personal protective equipment − Footwear protecting against risks in foundries and welding − Part 1: Requirements and test methods for protection against risks in foundries 個人防護具－防止鑄造及熔接中風險之鞋類－第1部：防護鑄造中風險之要求事項及試驗方法 |
|
|
|
CNS 15251-3
2019 Edition Information technology − Open document format for office applications (OpenDocument) v1.2 − Part 3: Packages 資訊技術－辦公室應用軟體OpenDocument v1.2 之開放文件格式－第3部：套件 |
|
|
|
CNS 14631
2019 Edition Structural sawn lumber used in platform construction 框組壁工法結構用製材 |
|
|
|
CNS 3290
2019 Edition Piano wire rods 鋼琴線 |
|
|
|
CNS 3473
2019 Edition Hydraulic brake wheel cylinders for automobiles 汽車用液壓煞車分泵 |
|
|
|
CNS 13987
2019 Edition Method of test for corrosion of fine ceramics in acid and alkaline solutions 精密陶瓷之酸、鹼腐蝕試驗法 |
|
|
|
CNS 14937
2019 Edition Method of test for effects of heat and air on asphaltic materials (Thin-film oven test) 柏油材料受熱及空氣影響試驗法（薄膜烘箱法） |
|
|
|
CNS 15030-17
2019 Edition Classification and labelling of chemicals - Acute toxicity 化學品分類及標示－急毒性物質 |
Translated |
|
|
CNS 14934-5
2019 Edition Electromagnetic compatibility (EMC) - Limits - Part 5: Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16A 電磁相容－限制值－第5部：額定電流大於16 A之設備於低電壓電源系統中電壓變動及閃爍之限制值 |
|
|
|
CNS 14253-3
2019 Edition Personal fall-arrest systems − Part 3: Self-retracting lifelines 個人擒墜系統−第3 部：自動回縮救生索 |
|
|
|
CNS 4273
2019 Edition Steel plates,sheets and strips for gas cylinders 高壓瓦斯容器用鋼板、鋼片及鋼帶 |
|
|
|
CNS 13306-2-3
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements 射頻擾動和免疫力量測設備與量測方法－第２－３部：擾動和免疫力量測方法－輻射擾動量測 |
|
|
|
CNS 13161
2019 Edition Codes for units of measure used in international trade 國際貿易之計量單位代碼 |
|
|
|
CNS 13181-2
2019 Edition The Method of Test of Presure Regulator and Vaporizers for LGP Automobile Fuel Systems 液化石油氣汽車燃氣系統–壓力調整器與氣化器檢驗法 |
Translated |
|
|
CNS 3801
2019 Edition Method of test for splitting tensile strength of cylindrical concrete specimens 混凝土圓柱試體劈裂抗張強度試驗法 |
|
|
|
CNS 14386-8
2019 Edition Power Filter Inductors for Electronic Equipment 電動機器腳踏車--車用馬達模擬功率試驗法 |
|
|
|
CNS 13921
2019 Edition Method of atomic emission spectrophotoelectric analysis for die casting zinc alloy 壓鑄鋅合金之光電式發光光譜分析法 |
|
|
|
CNS 16093-1
2019 Edition Welding and allied processes − Types of joint preparation − Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels 銲接及其相關製程－接頭準備型式－第1部：鋼的被覆銲條電弧銲接、氣體遮護金屬電弧銲接、氣銲、惰氣遮護金屬電弧銲接及能束銲接 |
|
|
|
CNS 6372
2019 Edition Polyester Blended Spun Yarns, Cotton System, Finished 聚酯混紡紗（棉紡式，本白紗） |
Translated |
| Find out:6360Items | To Page of: First -Previous-Next -Last | [54] [55] [56] [57] [58] [59] [60] |
