"et " CNS Standards List |
|
CNS 8411-1
2020 Edition Test methods for abrasion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Wheel wear test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－ 第１部：磨輪磨耗試驗法 |
|
|
|
CNS 7594
2020 Edition Helical Springs Made of Round Wire Dimensions for Cold Coiled Compression Springs with Wire Diameter From 0.5 mm up Wards 冷捲成形壓縮螺旋彈簧（簧線直徑０．５ｍｍ以上之構造尺度） |
|
|
|
CNS 15832-4-2
2020 Edition Method of test for paint components − Part 4-2: Analysis for components emitted from film − Volatile organic compounds 塗料成分試驗法－第4-2 部：塗膜釋出成分分析－揮發性有機化合物(VOC) |
|
|
|
CNS 3220-1
2020 Edition Sanitary ceramic ware – Tank for water closet 衛生陶瓷器－ 水箱 |
Translated |
|
|
CNS 14824
2020 Edition Method of test for detailed analysis of petroleum naphthas through n-nonane by capillary gas chromatography 正壬烷以下石油腦成分試驗法(毛細管柱氣相層析法) |
|
|
|
CNS 16143-2
2020 Edition Railway applications − Track − Performance requirements for fastening systems − Part 2: Fastening systems for concrete sleepers 鐵路應用－軌道－扣件系統之性能要求－第2部：混凝土軌枕用扣件系統 |
|
|
|
CNS 11424
2020 Edition Method of Test for Setting Time of Refractory Mortar 耐火墁料凝結時間試驗法 |
|
|
|
CNS 7525
2020 Edition Edible blended vegetable oil 食用調合植物油 |
|
|
|
CNS 10023
2020 Edition Plutonium By Controlled - Potential Coulometry 布層心體橡膠輸送帶 |
|
|
|
CNS 14104-3
2020 Edition Prosthetics and orthotics - Limb deficiencies - Part 2: Method of describing lower limb amputation stumps 義肢學與矯具學－肢體缺陷－第３部：上肢截肢之描述 |
|
|
|
CNS 11081
2020 Edition Method for Calculating Heat Balancing of Cement Rotary Kiln 水泥工業用窯爐之熱平衡計算方法 |
|
|
|
CNS 3-16
2020 Edition Engineering Drawing (Geometrical Tolerancing - Principles and Methods of Verification) 工程製圖（幾何公差–檢測原理與方法） |
|
|
|
CNS 14579-1
2020 Edition Method of test for prevention of fire for automobiles – Part 1: Fuel tanks 汽車火災預防檢驗法－第１部：燃料箱 |
|
|
|
CNS 15804
2020 Edition Oil of cassia, Chinese type − Determination of trans-cinnamaldehyde content − Gas chromatographic method on capillary columns 肉桂油(中國型)－反桂皮醛含量測定法－毛細管柱氣相層析法 |
|
|
|
CNS 13167
2020 Edition Safety Standards for Construction of Spindle Shapers 立軸機之構造安全基準 |
|
|
|
CNS 60335-2-2
2020 Edition Household and similar electrical appliances − Safety − Part 2-2: Particular requirements for vacuum cleaners and water-suction cleaning appliances 家用和類似用途電器－安全性－第2-2部：真空吸塵器及吸水清潔機之個別規定 |
|
|
|
CNS 15345-1
2020 Edition Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 1: Principles and specification for machinery manufacturers 機械安全－降低由機械釋放有害性物質對健康造成之風險－第１部：對機械製造商之原則及規範 |
|
|
|
CNS 8988
2020 Edition Chemical Reagent(Dry Loss Determination) 化學試藥（乾失量測定） |
|
|
|
CNS 20005
2020 Edition Information technology − Sensor networks − Services and interfaces supporting collaborative information processing in intelligent sensor networks 資訊技術－感測器網路－智慧感測器網路中支援協作資訊處理之服務及介面 |
|
|
|
CNS 15361
2020 Edition Determination of the ultimate anaerobic biodegradation and disintegration under high-solids anaerobic-digestion conditions of plastics - Method by analysis of released biogas 塑膠材料在高固體厭氧消化環境下最終厭氧生物分解性與崩解性測定法－釋出生物生成氣體分析法 |
|
|
|
CNS 11423
2020 Edition Method of Test for Grain Size of Refractory Mortar 耐火墁料細度試驗法 |
|
|
|
CNS 1706
2020 Edition Disodium Dihydrogen ethylenediamine Tetraacetate Dihydrate 化學試藥（伸乙二胺四乙酸二氫二鈉二水合物） |
|
|
|
CNS 9747
2020 Edition Method of Test for Fineness of Portland Cement by the Turbidimeter 卜特蘭水泥細度檢驗法（濁度計法） |
|
|
|
CNS 8408-2
2020 Edition Accelerated test methods for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloys -Part 2:Test for light fastness to ultra-violet light 鋁及鋁合金之著色陽極氧化膜加速耐光性試驗法－第２部：紫外光堅牢度試驗法 |
|
|
|
CNS 14315
2020 Edition Methods of test for bending fatigue of fine ceramics at room temperature 精密陶瓷室溫彎曲疲勞試驗法 |
|
|
|
CNS 14797
2020 Edition Mineral spirits（hydrocarbon dry cleaning solvent,petroleum spirits,stoddard solvent） 礦物型溶劑 |
|
|
|
CNS 61427-1
2020 Edition Secondary cells and batteries for renewable energy storage − General requirements and methods of test − Part 1: Photovoltaic off-grid application 再生能源儲能用二次單電池及電池組－一般要求及試驗法－第1部：太陽光電離網應用 |
|
|
|
CNS 14503-1
2020 Edition Evaluation methods for pitting corrosion of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart method 鋁及鋁合金之陽極氧化膜孔蝕評定法－第１部：圖示法 |
|
|
|
CNS 15200-4-1
2020 Edition Methods of test for paints - Part 4-1: Visual characteristics of film - Hiding power 塗料一般試驗法－第４－１部：塗膜視覺特性－遮蓋力 |
|
|
|
CNS 186
2020 Edition Numbers of Teeth of Change Gears for Geared Lathe, Milling Machine and Gear Generating Equipment 工具機用變換齒輪之齒數（導軸車床、銑床及製齒機用） |
|
| Find out:7275Items | To Page of: First -Previous-Next -Last | [49] [50] [51] [52] [53] [54] [55] |
