"as " CNS Standards List |
|
CNS 4021
2018 Edition Permissible Deviations in Dimensions Without Tolerance Indication (Iron Castings) 一般許可差（鐵鑄件） |
|
|
|
CNS 16060
2018 Edition Rubber, raw natural − Determination of plasticity retention index (PRI) 天然橡膠生膠－塑性殘留指數測定法 |
|
|
|
CNS 15145
2018 Edition Preparation of steel substrates before application of paints and related products-Surface roughness characteristics of blast-cleaned steel substrates (Method for the grading of surface profile of abrasive blast-cleaned steel-Comparator procedure) 調理肉品 |
|
|
|
CNS 4394-1
2018 Edition Plastics − Homopolymer and copolymer resins of vinyl chloride − Determination of volatile matter (including water) 塑膠－熱塑性塑膠射出成型試片－ 第1部：通則及模製多用途與棒形試片 |
|
|
|
CNS 62821-2
2018 Edition Halogen-free, low smoke, thermoplastic insulated and sheathed cables of rated voltages up to and including 450/750 V − Part 2: Test methods 額定電壓450/750 V 以下無鹵素低煙量熱塑性絕緣與被覆電纜－第2部：試驗法 |
|
|
|
CNS 4025
2018 Edition Permissbile Deviations in Dimensions Without Tolerance Indication (Aluminium Alloy Castings) 一般許可差（鋁合金鑄件） |
|
|
|
CNS 17050-1
2018 Edition Conformity assessment − Supplier's declaration of conformity − Part 1: General requirements 符合性評鑑－供應者之符合性聲明－第1 部：一般要求事項 |
|
|
|
CNS 10848
2018 Edition Valves for high pressure gas cylinders 高壓氣體容器用閥 |
Translated |
|
|
CNS 14200
2018 Edition Line transmission of non-telephone signals - Broadcasting type audiovisual multipoint systems and terminal equipment 非電話信號之線傳輸–廣播型式視聽多點系統和終端機設備 |
|
|
|
CNS 4735-1
2018 Edition 50Ω and 75Ω radio-frequency coaxial cables Part 1：General requirements and measuring methods 50Ω及75Ω射頻同軸電纜－第1部：通則與測試方法 |
|
|
|
CNS 15593-42
2018 Edition Electricity metering – Data exchange for meter reading, tariff and load control – Part 42: Physical layer services and procedures for connection-oriented asynchronous data exchange 電力計量－讀表、計費及負載控制之資料 交換－第42部：連接導向非同步資料 交換之實體層服務及程序 |
|
|
|
CNS 4234-3
2018 Edition Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress 不銹鋼結件之機械性質－第３部：無拉應力下之固定螺釘及類似結件 |
|
|
|
CNS 21003-7
2018 Edition Multilayer piping systems for hot and cold water installations inside buildings − Part 7: Guidance for the assessment of conformity 建築物內冷熱水裝置用多層管配管系統－第7部：符合性評鑑指引 |
|
|
|
CNS 7046-5
2018 Edition Plastics piping systems for hot and cold water installations − Polybutene (PB) − Part 3: Fittings 冷熱水裝置用塑膠管配管系統－聚丁烯(PB)－第5部：系統適合度 |
|
|
|
CNS 2828
2018 Edition Plastics − Reinforced moulding compounds and prepregs − Determination of apparent volatile-matter content 塑膠－狀態調節及試驗之 標準大氣狀態 |
|
|
|
CNS 15609-3
2018 Edition Thermoplastics pipes and fittings − Vicat softening temperature − Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings 熱塑性塑膠管與管件－衛氏軟化溫度－第3部：丙烯腈-丁二烯-苯乙烯及丙烯腈-苯乙烯-丙烯酸酯管與管件之試驗條件 |
|
|
|
CNS 8491
2018 Edition Marine Hull Cast Steel Angle Valves 船體用鑄鋼角閥 |
|
|
|
CNS 11320
2018 Edition Method of Test for Abrasion Resistance of Stone Subjected to Foot Traffic 石材腳踏磨損抗力試驗法 |
|
|
|
CNS 15590-7
2018 Edition Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 結件之機械性質－第7部：標稱直徑1 mm至10 mm螺栓與螺釘之扭力試驗及最小扭矩 |
|
|
|
CNS 15568
2018 Edition Protecting Equipment and Distribution of Three-Phase 220 V Motors for General Use 電擊防護－裝設及設備之一般觀念 |
|
|
|
CNS 15606-5
2018 Edition Plastics − Determination of tensile properties − Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites 塑膠－抗拉性能測定法－第5部：單向纖維強化塑膠複合材料之試驗條件 |
|
|
|
CNS 15612
2018 Edition Plastics − Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics − Part 1: Standard method 塑膠－吸水率測定法 |
|
|
|
CNS 12451
2018 Edition Methods for Measuring Specific Gravity of Solid 固體比重測定法 |
|
|
|
CNS 15041-1
2018 Edition Specification for non-invasive sphygmomanometers - Part 1: General requirements 非侵入式血壓計－第１部：一般規定 |
|
|
|
CNS 15609-1
2018 Edition Thermoplastics pipes and fittings − Vicat softening temperature − Part 1: General test method 熱塑性塑膠管與管件－衛氏軟化 溫度－第1部：一般試驗法 , |
|
|
|
CNS 13741-3
2018 Edition Information technology-Open systems interconnection-Virtual terminal basic class-application profiles-Part 3:AVT 22-S-mode forms application profile 資訊技術–開放系統互連–虛擬終端機基本類別–應用規範–第３部：同步模式表格應用規範 |
|
|
|
CNS 3376-5
2018 Edition Electrical apparatus of general use for explosive gas atmospheres-Part 5: Powder filling 〝q〞 爆炸性氣體環境用電機設備－第５部：填粉防爆構造〝ｑ〞 |
|
|
|
CNS 2183
2018 Edition Polyester Canvas 聚酯漆包銅線 |
Translated |
|
|
CNS 4022
2018 Edition Permissible Deviations in Dimensions Without Tolerance Indication (Die Castings) 一般許可差（壓鑄） |
|
|
|
CNS 184
2018 Edition Cylindrical gears for general and heavy engineering-Standard basic rack tooth profile 一般機械及重機械用圓柱齒輪─標準基準齒條齒廓 |
|
| Find out:3287Items | To Page of: First -Previous-Next -Last | [47] [48] [49] [50] [51] [52] [53] |
