": " CNS Standards List |
|
CNS 15660-5
2018 Edition Test conditions for numerically controlled turning machines and turning centres − Part 5: Accuracy of feeds, speeds and interpolations 數值控制車床及車削中心機之試驗條件－ 第5 部:進給、速率及插值之精度 |
|
|
|
CNS 13397
2018 Edition Information Processing Systems - Open Systems Interconnection - Basic Reference Model (Addendum 1: Connectionless - Mode Transmission) 資訊處理系統–開放系統互連–基本參考模型（免接模式傳輸） |
|
|
|
CNS 15593-42
2018 Edition Electricity metering – Data exchange for meter reading, tariff and load control – Part 42: Physical layer services and procedures for connection-oriented asynchronous data exchange 電力計量－讀表、計費及負載控制之資料 交換－第42部：連接導向非同步資料 交換之實體層服務及程序 |
|
|
|
CNS 7046-5
2018 Edition Plastics piping systems for hot and cold water installations − Polybutene (PB) − Part 3: Fittings 冷熱水裝置用塑膠管配管系統－聚丁烯(PB)－第5部：系統適合度 |
|
|
|
CNS 15652-4
2018 Edition Intelligent lighting systems − Part 4: Design guide for field area network 智慧照明系統－ 第4部：場域網路設計指引 |
|
|
|
CNS 15620-3
2018 Edition Insulation coordination for equipment within low-voltage system – Part 3: Use of coating, potting or moulding for protection against pollution 低電壓系統下設備之絕緣協調－第3 部：用於污染防護之塗裝、封裝或壓塑 |
|
|
|
CNS 15710-3
2018 Edition Effects of current on human beings and livestock – Part 3: Effects of currents passing through the body of livestock 電流在人體及家畜上之效應－第3 部：電流通過家畜軀體之效應 |
|
|
|
CNS 15130-3-25
2018 Edition Tests on electric cables under fire conditions - Part 3-25 : Test for vertical flame spread of vertically-mounted bunched wires or cables - Category D 電纜之燃燒試驗－第３－２５部：垂直敷設成束電線電纜之垂直火焰擴散試驗－類別Ｄ |
|
|
|
CNS 4394-2
2018 Edition Plastics − Injection moulding of test specimens of thermoplastic materials − Part 1: General principles, and moulding of multipurpose and bar test specimens 塑膠－熱塑性塑膠射出成型試片－第2部：小型拉伸試驗棒 |
|
|
|
CNS 15588-4
2018 Edition Electric traction − Rotating electrical machines for rail and road vehicles − Part 4: Permanent magnet synchronous electrical machines connected to an electronic converter 電力牽引－軌道及道路車輛用之旋轉電機－第4部：電子換流器供電之永磁同步電機 |
|
|
|
CNS 14545-6
2018 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 2:Glow-wire flammability test on materials 火災危險性試驗－第２部：試驗方法－第１章／第２單元：材料可燃性之熾熱線試驗 |
|
|
|
CNS 15590-7
2018 Edition Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 結件之機械性質－第7部：標稱直徑1 mm至10 mm螺栓與螺釘之扭力試驗及最小扭矩 |
|
|
|
CNS 14982-1
2018 Edition Miniature fuses - Part 1: Definitions for miniature fuses and general requirements for miniature fuse-links 小型熔線－第１部：小型熔線之定義及小型熔線體之通則 |
|
|
|
CNS 61347-1
2018 Edition Lamp controlgear − Part 1: General and safety requirements 光源控制裝置－第1部：通則及安全要求 |
|
|
|
CNS 15130-3-21
2018 Edition Tests on electric cables under fire conditions - Part 3-21 : Test for vertical flame spread of vertically-mounted bunched wires or cables - Category A F/R 電纜之燃燒試驗－第３－２１部：垂直敷設成束電線電纜之垂直火焰擴散試驗－類別Ａ Ｆ／Ｒ |
|
|
|
CNS 15703-2
2018 Edition Tool shanks with 7/24 taper for automatic tool changers – Part 2: Dimensions and designation of shanks of forms J, JD and JF 自動換刀器用7/24 錐度刀柄－第2 部：刀柄型式J、JD 及JF 之尺度及標示 |
|
|
|
CNS 15832-2-4
2018 Edition Method of test for coating components − Part 2-4: Component analysis in solvent soluble matter − Alkyd resin 塗料成分試驗法－第2-4部：溶劑可溶物中成分分析－醇酸樹脂 |
|
|
|
CNS 15468-5-1
2018 Edition Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety 燃料電池技術－第5-1部：可攜式燃料電池發電系統－安全 |
|
|
|
CNS 10239
2018 Edition Data Processing Vocabulary (Part 10: Operating Techniques and Facilities) 資料處理詞彙（第１０部：作業技術及裝備） |
|
|
|
CNS 13853-2
2018 Edition Information technology - Computer graphics - Metafile for the storage and transfer of picture description information - Part 2:Character encoding 資訊技術–電腦圖形–儲存與轉送圖象描述資訊的元檔–第２部：字元編碼 |
|
|
|
CNS 15691-1
2018 Edition Aseptic processing of health care products − Part 1: General requirements 健康照護產品之無菌操作－第 1 部:一般要求 |
|
|
|
CNS 15588-1
2018 Edition Electric traction - Rotating electrical machines for rail and road vehicles - Part 1: Machines other than electronic converter-fed alternating current motors 電力牽引－軌道及道路車輛用之旋轉電機－第1部：旋轉電機(不含電子換流器供電之 交流電動機) |
|
|
|
CNS 14233-11
2018 Edition Information processing - SGML support facilities - Techniques for using SGML - Part 11:Application at ISO central secretariat for international standards and technical reports 資訊處理–標準通用標示語言支援設施–標準通用標示語言的使用技術–第１１部：ＩＳＯ中央秘書處之國際標準與技術報告應用 |
|
|
|
CNS 13188-3
2018 Edition Codes for the representation of names of languages part 3: Alpha-3 code for comprehensive coverage of languages 語言名稱代碼表示法－第3部：全面涵蓋語言之三字母代碼 |
|
|
|
CNS 14637-3
2018 Edition Test code for machine tools − Part 3: Determination of thermal effects 工具機試驗規範－第3部：熱效應之決定 |
|
|
|
CNS 14213-1
2018 Edition Information technology - Open systems interconnection - Procedures for the operation of OSI registration authorities - Part 1:General procedures 資訊技術–開放系統互連–開放系統互連註冊機構作業程序–第１部：一般程序 |
|
|
|
CNS 15569-1
2018 Edition Hydraulic fluid power - Filter elements - Part 1: Verification of collapse/burst pressure rating 液壓流體動力－過濾器濾心－第1部：查證崩潰/爆裂壓力額定值 |
|
|
|
CNS 12972-7
2018 Edition Office Machine - Vocabulary - Section 07 : Postal franking machines 事務機器–字彙–第七部：自動郵資蓋印機 |
|
|
|
CNS 18080-2
2018 Edition Textiles − Test methods for evaluating the electrostatic propensity of fabrics − Part 2: Test method using rotary mechanical friction 紡織品－靜電性評估法－ 第2部：旋轉機械摩擦試驗法 |
|
|
|
CNS 14356-1
2018 Edition Information Technology--Open Document Architecture(ODA)and Interchange Format:Document Structure 資訊技術－開放文件架構與交換格式：文件結構 |
|
| Find out:2437Items | To Page of: First -Previous-Next -Last | [41] [42] [43] [44] [45] [46] [47] |
