"V " CNS Standards List |
|
CNS 5336
2019 Edition Methods of eleVated temperature tensile test for iron,steels and heat resisting alloys 鋼鐵及耐熱合金之高溫拉伸試驗法 |
|
|
|
CNS 20349-2
2019 Edition Personal protectiVe equipment − Footwear protecting against risks in foundries and welding − Part 2: Requirements and test methods for protection against risks in welding and allied processes 個人防護具－防止鑄造及熔接中風險之鞋類－第2部：防護熔接及類似製程風險之要求事項及試驗方法 |
|
|
|
CNS 15630
2019 Edition Self-ballasted LED lamps for general lighting serVices with supply voltages > 50 V − Performance requirements 一般照明用安定器內藏式LED 燈泡(供應電壓大於50 V)－性能要求 |
|
|
|
CNS 11030
2019 Edition OVerlaid glulam for decorative use 化粧貼面裝修用集成材 |
|
|
|
CNS 15660-3
2019 Edition Test conditions for numerically controlled turning machines and turning centres − Part 3: Geometric tests for machines with inVerted vertical workholding spindles 數值控制車床及車削中心機之試驗條件－ 第3部：倒立式工件夾持主軸工具機之幾何試驗 |
|
|
|
CNS 7892
2019 Edition Speed indicating deVices for automobiles 汽車用速率指示裝置 |
|
|
|
CNS 5808
2019 Edition Methods of Test for Strength Properties of AdhesiVes for Wood in Shear by Tension Loading 木材用黏著劑之抗剪強度測定法（拉力負荷法） |
|
|
|
CNS 15051
2019 Edition Fat and oil deriVatives - Fatty acid methyl esters (FAME) - Determination of ester and linolenic acid methyl ester contents 油脂衍生物（脂肪酸甲酯）－總脂肪酸甲酯及次亞麻油酸甲酯含量測定法 |
|
|
|
CNS 15200-9-1
2019 Edition Methods of test for paints – Part 9-1: Coating powders – Determination of gel time of thermosetting coating powders at a giVen temperature 塗料一般試驗法－第9-1 部：粉體塗料－指定溫度下熱固性粉體塗料膠化時間測定 |
|
|
|
CNS 14816-1
2019 Edition Low-Voltage switchgear and controlgear − Part 1: General rules 低電壓開關裝置及控制裝置－第1部：通則 |
|
|
|
CNS 13959
2019 Edition Method of test for compressiVe strength of fine ceramics 精密陶瓷壓縮強度試驗法 |
|
|
|
CNS 15040
2019 Edition Paints and Varnishes - Determination of the volatile organic compound content of low - VOC emulsion paints (in-can VOC) 塗料與清漆－低ＶＯＣ乳膠漆（罐內ＶＯＣ）揮發性有機化合物含量之測定 |
|
|
|
CNS 15130-2-1
2019 Edition Tests on electric and optical fibre cables under fire conditions − Part 2-1: Test for Vertical flame propagation for a single small insulated wire or cable – Apparatus 電纜及光纜之燃燒試驗－ 第2-1部：單條小型絕緣電線或電纜之垂直火焰延燃試驗－ 裝置 |
|
|
|
CNS 15755-2-1
2019 Edition ConVersion tables for units − Part 2-1: Length − Millimeter and inch 單位換算表－第2-1 部：長度－毫米與英寸 |
|
|
|
CNS 4063
2019 Edition Reinforced Concrete CoVers for Ditches (U Type) 鋼筋混凝土Ｕ形溝用蓋 |
Translated |
|
|
CNS 14499
2019 Edition Road Vehicles − Test methods for electrical disturbances from electrostatic discharge 道路車輛－ 靜電放電之電擾動試驗法 |
|
|
|
CNS 1163
2019 Edition Method of test for bulk density and Voids in aggregate 粒料容積密度與空隙率試驗法 |
|
|
|
CNS 15117
2019 Edition PhotoVoltaic systems − Power conditioners − Procedure for measuring efficiency 太陽光電系統－電力調節器－量測效率之程序 |
|
|
|
CNS 11818
2019 Edition Laminated Veneer lumber 單板層積材 |
|
|
|
CNS 14432-2
2019 Edition Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions − Method by analysis of eVolved carbon dioxide − Part 2: Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test 塑膠材料在控制堆肥條件下最終好氧生物分解度測定法－二氧化碳釋出量分析法－第2部：實驗室規模重量測定法 |
|
|
|
CNS 16101
2019 Edition Specification and qualification of welding procedures for metallic materials − Qualification based on preVious welding experience 金屬材料銲接程序規範書及其檢定－依〝先前銲接經驗〞檢定 |
|
|
|
CNS 7270
2019 Edition Method of Test for Vinylon Ropes 維尼龍繩索檢驗法 |
|
|
|
CNS 9487
2019 Edition Bronze Screw down Check Globe Valves for Marine Use (5 kgf / ㎠) (Union Bonnet Type) 船用青銅管套帽型螺桿止回球形閥（5 kgf/㎠） |
|
|
|
CNS 15725
2019 Edition Belt driVes − Pulleys for V-belts (system based on datum width) − Geometrical inspection of grooves 皮帶傳動－使用三角皮帶之皮帶輪(以基準寬度為基礎之系統)－溝槽之幾何檢驗 |
|
|
|
CNS 4767
2019 Edition Cotton Blended Spun Yarns and Viscose Rayon Blended Spun Yarns, Cotton System,Finished 棉混紡紗及黏液嫘縈棉混紡紗（棉紡式，漂染紗） |
|
|
|
CNS 8944
2019 Edition Method of Test for Tyre Valves for Automobiles 汽車輪胎氣門嘴檢驗法 |
|
|
|
CNS 30
2019 Edition Belt driVes − Pulleys − Quality, finish and balance 皮帶傳動－皮帶輪－品質、加工及平衡 |
|
|
|
CNS 15077-3
2019 Edition Test conditions for machining centres - Part 3 : Geometric tests for machines with integral indexable or continuous uniVersal heads (vertical Z-axis) 切削中心機之檢驗條件－第３部：具整合型分段指示或連續萬向分度頭之機器幾何檢驗（垂直Ｚ軸） |
|
|
|
CNS 15186-2
2019 Edition Cleanrooms and associated controlled enVironments – Part 2: Specifications for testing and monitoring to prove continued compliance with CNS 15186-1 潔淨室及其附屬之控制環境－第２部：確保持續符合ＣＮＳ １５１８６－１之測試與監測規範 |
|
|
|
CNS 15685
2019 Edition Method of test for grain size of coated abrasiVe microgrits (P240-P2500) 砂紙、砂布用細粒磨料粒度試驗法 |
|
| Find out:4669Items | To Page of: First -Previous-Next -Last | [40] [41] [42] [43] [44] [45] [46] |
