"1,2 " CNS Standards List |
|
CNS 15562-10
2019 Edition Stationary training equipment − Part 10: Exercise bicycles with a fixed wheel or without freewheel, additional specific safety requirements and test methods 固定式訓練器材－第10部：具固定輪或無自由輪健身車之附加特定安全要求與試驗法 |
|
|
|
CNS 15130-2-2
2019 Edition Tests on electric and optical fibre cables under fire conditions − Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable – Procedure for diffusion flame 電纜及光纜之燃燒試驗－ 第2-2部:單條小型絕緣電線或電纜之垂直火焰延燃試驗－ 擴散火焰之程序 |
|
|
|
CNS 13297
2019 Edition Method of test for abrasion resistance of concrete by sandblasting 混凝土製品耐磨性試驗法(噴砂法) |
|
|
|
CNS 15660-2
2019 Edition Test conditions for numerically controlled turning machines and turning centres − Part 2: Geometric tests for machines with a vertical workholding spindle 數值控制車床及車削中心機之試驗條件－ 第2部：立式工件夾持主軸工具機之幾何試驗 |
|
|
|
CNS 1235
2019 Edition Method of test for bleeding of concrete 混凝土泌水試驗法 |
|
|
|
CNS 15252
2019 Edition Industrial automation systems and integration - Open systems application integration framework - Part 5: Reference description for HDLC-based control systems 工業自動化系統及整合－開放系統應用整合架構－第５部：基於ＨＤＬＣ之控制系統參考說明 |
|
|
|
CNS 15760-2
2019 Edition Footwear − General test methods – Part 2: Sampling location, preparation and duration of conditioning of samples and test pieces 鞋類－ 一般試驗法－ 第2 部： 樣品與試片之取樣部位、製備及狀態調節時間 |
|
|
|
CNS 15755-3-2
2019 Edition Conversion tables for units − Part 3-2: Area − Square meter and square yard 單位換算表－第3-2 部：面積－平方公尺與平方碼 |
|
|
|
CNS 5812
2019 Edition Methods of Test for Peel Strength of Adhesives 黏著劑之剝離強度測定法 |
|
|
|
CNS 11302
2019 Edition Iron and steel-Methods for determination of chromium content 鐵及鋼─鉻定量法 |
|
|
|
CNS 15242
2019 Edition Disposable body warmers 拋棄式暖暖包 |
|
|
|
CNS 15203
2019 Edition Oils of bergamot, lemon, citron and lime, fully or partially reduced in bergapten - Determination of bergapten content by high-pressure liquid chromatography (HPLC) 香檸檬油、檸檬油、柑橘油及萊姆油－香檸檬烯含量測定高效能液相層析法（ＨＰＬＣ） |
|
|
|
CNS 14432-2
2019 Edition Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions − Method by analysis of evolved carbon dioxide − Part 2: Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test 塑膠材料在控制堆肥條件下最終好氧生物分解度測定法－二氧化碳釋出量分析法－第2部：實驗室規模重量測定法 |
|
|
|
CNS 10273-4
2019 Edition Rubber, unvulcanized − Determinations using a shearing-disc viscometer − Part 4: Determination of the Mooney stress-relaxation rate 未硫化橡膠－使用剪力-圓盤型黏度計－第4 部:木尼應力-鬆弛速率之測定 |
|
|
|
CNS 11206
2019 Edition Iron and steel─Methods for atomic absorption spectrometric analysis 鐵及鋼─原子吸收光譜分析法 |
|
|
|
CNS 20349-1
2019 Edition Personal protective equipment − Footwear protecting against risks in foundries and welding − Part 1: Requirements and test methods for protection against risks in foundries 個人防護具－防止鑄造及熔接中風險之鞋類－第1部：防護鑄造中風險之要求事項及試驗方法 |
|
|
|
CNS 16083-2
2019 Edition Viscosity and viscometric fixed points of glass − Part 2: Determination of annealing point and strain point by fiber elongation 玻璃黏度和黏度固定點－第2部：以玻璃絲拉伸法測定退火點和應變點 |
|
|
|
CNS 12456
2019 Edition Corrosion Inhibitor for Reinforcing Steel in Concrete 鋼筋混凝土用防銹劑 |
|
|
|
CNS 12103
2019 Edition Method of test for formaldehyde content of paper products by acetylacetone 紙製品甲醛含量試驗法(乙醯丙酮法) |
|
|
|
CNS 15200-1-5
2019 Edition Testing methods for paints - Part 1-5 : General rule - Coating of test panel (brush application) 塗料一般試驗方法－第１－５部：通則－試驗板之塗裝（刷塗） |
|
|
|
CNS 15721
2019 Edition Self adhesive tapes – Determination of peel adhesion properties 感壓性黏膠帶－剝離黏著力測定法 |
|
|
|
CNS 14599
2019 Edition Flux cored wires for CO2 gas shielded arc welding of atmospheric corrosion resisting steel 耐候鋼CO2 氣體遮護電弧銲接用包藥銲線 |
|
|
|
CNS 14622-2
2019 Edition Sterilization of health care products − Biological indicators − Part 2: Biological indicators for ethylene oxide sterilization processes 健康照護產品滅菌－生物指示劑－第2 部：環氧乙烷滅菌程序之生物指示劑 |
|
|
|
CNS 14622-1
2019 Edition Sterilization of health care products − Biological indicators − Part 1: General requirements 健康照護產品滅菌－生物指示劑－第1 部：一般 |
|
|
|
CNS 15762-4
2019 Edition Footwear − Test methods for uppers − Part 4: Tensile strength and elongation of uppers 鞋類─鞋面試驗法─第4 部：鞋面之抗拉強度及伸長率 |
|
|
|
CNS 12514-4
2019 Edition Fire-resistance tests – Elements of building construction – Part 4: Specific requirements for loadbearing vertical separating elements 建築物構造構件耐火試驗法－第4 部：承重垂直區劃構件特定要求 |
|
|
|
CNS 13181-2
2019 Edition The Method of Test of Presure Regulator and Vaporizers for LGP Automobile Fuel Systems 液化石油氣汽車燃氣系統–壓力調整器與氣化器檢驗法 |
Translated |
|
|
CNS 15200-1-6
2019 Edition Testing methods for paints - Part 1-6: General rule - Temperatures and humidities for conditioning and testing 塗料一般試驗方法－第１－６部：通則－調節與試驗之溫度及濕度 |
|
|
|
CNS 14128
2019 Edition Method of impact test for instrument panel of passenger cars 小客車用儀表板衝擊試驗法 |
|
|
|
CNS 15725
2019 Edition Belt drives − Pulleys for V-belts (system based on datum width) − Geometrical inspection of grooves 皮帶傳動－使用三角皮帶之皮帶輪(以基準寬度為基礎之系統)－溝槽之幾何檢驗 |
|
| Find out:4607Items | To Page of: First -Previous-Next -Last | [40] [41] [42] [43] [44] [45] [46] |
