"LE " CNS Standards List |
|
CNS 981
2020 Edition Bone china tabLEwares 骨瓷質食器 |
|
|
|
CNS 16135
2020 Edition Test method for determining tensiLE properties of geogrids by the single or multi-rib tensile method 地工格網抗拉特性－單肋條或多肋條拉伸試驗法 |
|
|
|
CNS 6921
2020 Edition Rubber handLEbar grip for bicycle 自行車用橡膠握套 |
|
|
|
CNS 24508
2020 Edition Ergonomics − AccessibLE design − Guidelines for designing tactile symbols and characters 人因工程學－無障礙設計－觸覺符號與字符之設計指導綱要 |
|
|
|
CNS 5788
2020 Edition Turn Signal Flashers for AutomobiLEs 汽車用轉向信號燈閃光器 |
Translated |
|
|
CNS 6903
2020 Edition CabLE Terminals for Automobiles (Type LB) 汽車用電線端子（橫接環眼型） |
|
|
|
CNS 7136
2020 Edition Cylinder Liners for AutomobiLE Engines (Cast Iron) 汽車引擎用鑄鐵汽缸襯套 |
Translated |
|
|
CNS 16143-2
2020 Edition Railway applications − Track − Performance requirements for fastening systems − Part 2: Fastening systems for concrete sLEepers 鐵路應用－軌道－扣件系統之性能要求－第2部：混凝土軌枕用扣件系統 |
|
|
|
CNS 7029
2020 Edition Shape, Dimensions and Travel AngLEs of Drawbar Eyes for Full Trailers 全拖車用拖桿環首之形狀、尺度及活動範圍 |
|
|
|
CNS 7023
2020 Edition CabLE Terminals of Spark Plug for Automobiles ( Type IB ) 汽車用火星塞電線端子（ＩＢ型） |
|
|
|
CNS 7024
2020 Edition CabLE Terminals for Automobiles (Type CA) 汽車用電線端子（塞型陽端子） |
|
|
|
CNS 147
2020 Edition Cylindrical Shaft End (for Assembling Coupling, PulLEy and Gear) 柱軸梢（用以承裝聯軸器，皮帶輪與齒輪） |
|
|
|
CNS 12835-4
2020 Edition Plastics piping systems for the supply of gaseous fuels − PolyethyLEne (PE) − Part 3: Fittings 燃氣用塑膠配管系統－聚乙烯(PE)－第4部：閥 |
|
|
|
CNS 494
2020 Edition ParalLEl Pipe Threads 平行管螺紋 |
|
|
|
CNS 1501
2020 Edition General RuLEs for Test Methods of Reagents 化學試藥試驗法通則 |
|
|
|
CNS 7594
2020 Edition Helical Springs Made of Round Wire Dimensions for Cold CoiLEd Compression Springs with Wire Diameter From 0.5 mm up Wards 冷捲成形壓縮螺旋彈簧（簧線直徑０．５ｍｍ以上之構造尺度） |
|
|
|
CNS 3564-2
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 2: Determination of low-temperature brittLEness 硫化或熱塑性橡膠－低溫性質之測定－第2部：低溫脆性測定法 |
|
|
|
CNS 60335-2-2
2020 Edition Household and similar eLEctrical appliances − Safety − Part 2-2: Particular requirements for vacuum cleaners and water-suction cleaning appliances 家用和類似用途電器－安全性－第2-2部：真空吸塵器及吸水清潔機之個別規定 |
|
|
|
CNS 3-16
2020 Edition Engineering Drawing (Geometrical ToLErancing - Principles and Methods of Verification) 工程製圖（幾何公差–檢測原理與方法） |
|
|
|
CNS 3325
2020 Edition Standard Classification of CastabLE Refractories 可鑄耐火物分級標準 |
|
|
|
CNS 4318
2020 Edition ISO Miniature Screw Threads-ToLErances 公制精細小螺紋公差（ＩＳＯ制） |
Translated |
|
|
CNS 9567
2020 Edition Withdrawal SLEeves for Rolling Bearings 滾動軸承拔出套筒 |
|
|
|
CNS 15317-3
2020 Edition Crosslinked polyethyLEne (PE-X) pipe for hot and cold water conveyance - Part 3: Fittings 冷熱水輸送用交連聚乙烯管－第３部：管件 |
|
|
|
CNS 4238
2020 Edition Finishes and ToLErances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 12616
2020 Edition Method of Test for ELEctrical Conductivity of Aviation and Distillate Fuels Containing a Static Dissipator Additive 航空燃油含靜電逸散劑導電度測定法 |
|
|
|
CNS 14824
2020 Edition Method of test for detaiLEd analysis of petroleum naphthas through n-nonane by capillary gas chromatography 正壬烷以下石油腦成分試驗法(毛細管柱氣相層析法) |
|
|
|
CNS 9597
2020 Edition Suspension Coil Springs for AutomobiLEs 汽車用懸吊裝置螺旋彈簧 |
|
|
|
CNS 10023
2020 Edition Plutonium By ControlLEd - Potential Coulometry 布層心體橡膠輸送帶 |
|
|
|
CNS 15317-1
2020 Edition Crosslinked polyethyLEne (PE-X) pipe for hot and cold water conveyance - Part 1: General 冷熱水輸送用交連聚乙烯管－第１部：通則 |
|
|
|
CNS 15354
2020 Edition Test methods for dieLEctric strength of anodic oxide coatings on aluminium and aluminium alloys 鋁及鋁合金之陽極氧化膜絕緣性試驗法 |
|
| Find out:6143Items | To Page of: First -Previous-Next -Last | [38] [39] [40] [41] [42] [43] [44] |
