"D C " CNS Standards List |
|
CNS 11072
1984 Edition Method of X-Ray Fluorescence Spectrometric Analysis of Iron and Steel 鐵及鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 6408
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算－齒廓面作用帶因數Ｚ H |
|
|
|
CNS 6407
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算－負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 10502
1984 Edition Method for X-Ray Fluorescence Spectrometric Analysis of Pig Iron, Cast Iron, Carbon Steel and Low Alloy Steel 生鐵、鑄鐵、碳鋼及低合金鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 10503
1984 Edition Emission-Spectroscopic Analysis for Pig Iron anD Cast Iron 生鐵及鑄鐵之發光光譜分析法 |
|
|
|
CNS 6409
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Material Factor Zм 圓柱齒輪與傘齒輪之負載能力計算－材料因數ＺM |
|
|
|
CNS 5283
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 4732
1984 Edition Knurled Nuts with Ring 有環滾紋螺帽 |
|
|
|
CNS 11154
1984 Edition Grease Guns-Rush Type Hand Guns 手用衝壓式黃油槍 |
|
|
|
CNS 4731
1984 Edition Knurled Nuts for Drawing Instruments 滾紋螺帽（製圖儀器用） |
|
|
|
CNS 4729
1984 Edition Round Nuts 圓螺帽 |
|
|
|
CNS 5280
1984 Edition Helix Angles for Cylindrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 6414
1984 Edition Basic Rack of Straight Bevel Gears for General and Heavy Engineering 直齒傘齒輪之基準齒條(一般機械及重機械用) |
|
|
|
CNS 11070
1984 Edition General Rules of Determination for Carbon in Metallic Materials 金屬材料中碳定量法通則 |
|
|
|
CNS 11159
1984 Edition Tungsten-Carbide Tip Core Drills 碳化鎢鑽刃留心鑽頭 |
|
|
|
CNS 5284
1984 Edition Addendum Modification of Spur Gears in the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 11151
1984 Edition Method of Test for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 5285
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 10225
1984 Edition Test Code for Accuracy of Drum Sanders 圓筒砂光機精度檢驗標準 |
|
|
|
CNS 11112
1984 Edition Methods of Chemical Analysis for Lead Ingot 鉛錠分析法 |
|
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 11153
1984 Edition Method of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 10795
1984 Edition Insulation Resistance Testers (Magneto Generator Operated) 絕緣電阻計（發電機式） |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 5022
1984 Edition Thyristorstack for Welding Machine 電焊機用閘流調節器 |
Translated |
|
|
CNS 10786
1984 Edition Test Code for Performance of Drum Sanders 圓筒砂光機動態檢驗法 |
|
|
|
CNS 10849
1984 Edition Screw Threads of Valves for High Pressure Gas Cylider 高壓鋼瓶閥螺紋標準 |
Translated |
|
|
CNS 5026
1984 Edition Welding Transformers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 2521
1984 Edition Laminated Aluminium Foils 貼合積層鋁箔 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [419] [420] [421] [422] [423] [424] [425] |
