"D " CNS Standards List |
|
CNS 11154
1984 Edition Grease Guns-Rush Type HanD Guns 手用衝壓式黃油槍 |
|
|
|
CNS 4664
1984 Edition CloseD Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽（封閉式，嵌於塑膠製品內） |
Translated |
|
|
CNS 11153
1984 Edition MethoD of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 11151
1984 Edition MethoD of Test for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics MoulDings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 5284
1984 Edition ADdendum Modification of Spur Gears in the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 6411
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 4663
1984 Edition CloseD Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽（片封式，嵌於塑膠製品內） |
|
|
|
CNS 6409
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Material Factor Zм 圓柱齒輪與傘齒輪之負載能力計算－材料因數ＺM |
|
|
|
CNS 6408
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算－齒廓面作用帶因數Ｚ H |
|
|
|
CNS 6407
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算－負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 10503
1984 Edition Emission-Spectroscopic Analysis for Pig Iron anD Cast Iron 生鐵及鑄鐵之發光光譜分析法 |
|
|
|
CNS 5283
1984 Edition Accuracy of CylinDrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 10502
1984 Edition MethoD for X-Ray Fluorescence Spectrometric Analysis of Pig Iron, Cast Iron, Carbon Steel and Low Alloy Steel 生鐵、鑄鐵、碳鋼及低合金鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 5285
1984 Edition Accuracy of CylinDrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 1419
1984 Edition MethoD of Test for Acetone 丙酮檢驗法 |
|
|
|
CNS 10786
1984 Edition Test CoDe for Performance of Drum Sanders 圓筒砂光機動態檢驗法 |
|
|
|
CNS 10761
1984 Edition MethoD of Test for Surface Wax on Waxed Paper or Paperboard 蠟紙及蠟紙板之表面蠟量試驗法 |
Translated |
|
|
CNS 10734
1984 Edition MethoD of Test for the Plastic Rims of Bicycle 平車或跑車型自行車塑膠輪圈檢驗法 |
|
|
|
CNS 11159
1984 Edition Tungsten-CarbiDe Tip Core Drills 碳化鎢鑽刃留心鑽頭 |
|
|
|
CNS 5280
1984 Edition Helix Angles for CylinDrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 6412
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 5026
1984 Edition WelDing Transformers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 5022
1984 Edition Thyristorstack for WelDing Machine 電焊機用閘流調節器 |
Translated |
|
|
CNS 5027
1984 Edition Control Timers for Resistance WelDing Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 5028
1984 Edition Rectifier Type DC Arc Welding Machines with Drooping Characteristic 穩流整流式直流電弧電焊機 |
|
|
|
CNS 5030
1984 Edition Projection WelDing Machine 凸壓電焊機 |
|
|
|
CNS 2521
1984 Edition LaminateD Aluminium Foils 貼合積層鋁箔 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [419] [420] [421] [422] [423] [424] [425] |
