"4 " CNS Standards List| Bushings Jigs | Wood treated | Communication networks | Non Thread | Industrial, scientific | Calibration Caculation | Methods Noise | Hand held | |
|
CNS 11741
2020 Edition Method of Test for Thermal Expansion and Shrinkage of Insulating Fire Bricks 絕熱耐火磚熱脹縮試驗法 |
|
|
|
CNS 14104-1
2020 Edition Prosthetics and orthotics - Classification and description of prosthetic components - Part 3: Description of upper-limb prosthetic components 義肢學與矯具學－肢體缺陷－第１部：先天性肢體缺陷之描述 |
|
|
|
CNS 7594
2020 Edition Helical Springs Made of Round Wire Dimensions for Cold Coiled Compression Springs with Wire Diameter From 0.5 mm up Wards 冷捲成形壓縮螺旋彈簧（簧線直徑０．５ｍｍ以上之構造尺度） |
|
|
|
CNS 2045
2020 Edition Zinc Nitrate 化學試藥（硝酸鋅） |
|
|
|
CNS 15423-1
2020 Edition Equipment for water supply service – Part 1: Test methods of hydrostatic pressure 自來水用器具－第1部：耐壓試驗法 |
|
|
|
CNS 7554
2020 Edition Slip-on Welding Steel Pipe Flanges (10 kgf/㎠) 滑入熔接式鋼製管凸緣（10 kgf/㎠） |
|
|
|
CNS 7534
2020 Edition Personal protective equipment for work positioning and prevention of falls from a height − Belts for work positioning and restraint and work positioning lanyards 工作定位及防止由高處墜落之個人防護具－工作定位與限制帶及工作定位索 |
|
|
|
CNS 14177
2020 Edition Quality management systems － Guidelines for quality plans 品質管理系統－品質計畫指導綱要 |
|
|
|
CNS 499
2020 Edition ISO Metric Fine Screw Threads (Diameters From 1 to 3.5mm and Pitches 0.2 to 0.35mm) 公制細螺紋2（ISO制）（標稱直徑1至3.5公釐，螺距0.2至0.35公釐） |
Translated |
|
|
CNS 14964-2
2020 Edition Wheelchairs − Part 2: Determination of dynamic stability of electrically powered wheelchairs 輪椅－第2部：電動輪椅動態穩定性之測定 |
|
|
|
CNS 61427-1
2020 Edition Secondary cells and batteries for renewable energy storage − General requirements and methods of test − Part 1: Photovoltaic off-grid application 再生能源儲能用二次單電池及電池組－一般要求及試驗法－第1部：太陽光電離網應用 |
|
|
|
CNS 14942
2020 Edition Electric lighting of passenger stock 軌道客車電氣照明 |
|
|
|
CNS 3389
2020 Edition Method for Calculating Viscosity Index from Kinematic Viscosity at 40 and 100 Degree C 由40°及100℃動黏度計算黏度指數之方法 |
|
|
|
CNS 14474
2020 Edition Method of test for density and relative density of liquids by digital density meter 液態油品密度及比重測定法(數位式密度計法) |
|
|
|
CNS 4797-7
2020 Edition Safety of toys − Part 7: Organic chemical compounds − Sample preparation and extraction 玩具安全－第7部：有機化合物－試樣製備及萃取 |
|
|
|
CNS 1547
2020 Edition Ammonium Carbonate (Reagent) 化學試藥（碳酸銨） |
|
|
|
CNS 14569
2020 Edition Method of test for steel track bolts and nuts 軌道用螺栓及螺帽檢驗法 |
|
|
|
CNS 14690
2020 Edition Aliphatic solvents 脂肪烴溶劑 |
|
|
|
CNS 5435
2020 Edition Dimensions of Starter Pinions and Ring Gears for Automobiles 汽車用起動電動機小齒輪及環形齒輪之尺度 |
|
|
|
CNS 4797-8
2020 Edition Safety of toys − Part 8: Organic chemical compounds − Methods of analysis 玩具安全－第8部：有機化合物－分析方法 |
|
|
|
CNS 493
2020 Edition Fine Whitworth Thread (Diameter Ranging From 20 to 189 mm, with Tip Clearance) 韋氏細螺紋（尖端有空隙，直徑自２０至１８９公釐） |
|
|
|
CNS 4238
2020 Edition Finishes and Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 7864
2020 Edition Laminated Spring Spring Link Washer Bearing Plates for Spring Suspension 彈簧板端導托–懸吊彈簧用 |
Translated |
|
|
CNS 7114
2020 Edition Cast Steel Flanged Gate Valves (20 kgf/㎠) (Outside Screw Type) 鑄鋼凸緣型閘閥（20 kgf/㎠）（閥桿上升型） |
Translated |
|
|
CNS 14647
2020 Edition Structural wood-based panel 結構用木質嵌板 |
|
|
|
CNS 14316
2020 Edition General rules of the sample preparation for particle size analysis of fine ceramic raw powder 精密陶瓷原料粒徑分布測定之試樣調製通則 |
|
|
|
CNS 8483
2020 Edition Control Cables for Motor - Cycle 兩輪機車用操縱線 |
Translated |
|
|
CNS 14579-2
2020 Edition Method of test for prevention of fire for automobiles – Part 2: In the event of collision for passenger cars 汽車火災預防檢驗法－第２部：小客車碰撞 |
|
|
|
CNS 61439-4
2020 Edition Low-voltage switchgear and controlgear assemblies − Part 4: Particular requirements for assemblies for construction sites (ACS) 低電壓開關裝置及控制裝置組裝品－第4部：建築工地用組裝品(ACS)之個別要求 |
|
|
|
CNS 14566
2020 Edition Sleeper screws (Screw spikes) 螺旋道釘 |
|
| Find out:6238Items | To Page of: First -Previous-Next -Last | [36] [37] [38] [39] [40] [41] [42] |
