"f " CNS Standards List |
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for Plastics 塑膠型模用頂出套筒 |
|
|
|
CNS 12071
1987 Edition Angle Pin of Die Casting Molds 壓鑄模用斜角撐銷 |
|
|
|
CNS 11906
1987 Edition Method of Test for Fiber Optic Devices (FOTP-84 Jacket Self-Adhesion (Blocking) Test for Fiber Optic Cable) 光纖裝置檢驗法（光纜被覆自黏性試驗FOTP-84） |
|
|
|
CNS 11937
1987 Edition Runner Pull Pins of Molds for Plastics 塑膠型模用流道拉銷 |
|
|
|
CNS 8228
1987 Edition Method of Test for Dry Reed Switches (Dielectric) 乾式簧開關檢驗法（電介質） |
|
|
|
CNS 11907
1987 Edition Method of Test for Fiber Optic Devices (FOTP-99 Gas Flame Test for Special Purpose Fiber Optic Cable) 光纖裝置檢驗法（特種用途光纜之火焰試驗FOTP-99） |
|
|
|
CNS 11902
1987 Edition Method of Test for Fiber Optic Devices (FOTP-52 Temperature Dependence of Attenuation for Optical Fibers) 光纖裝置檢驗法（溫度變化對光纖衰減之影響FOTP-52） |
|
|
|
CNS 11901
1987 Edition Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 8227
1987 Edition Method of Test for Dry Reed Switches (Operation Parameters) 乾式簧開關檢驗法（動作參數） |
|
|
|
CNS 11900
1987 Edition fixed Ceramic Capacitors for Electronic Equipment (Semiconductor) 電子設備用陶瓷固定電容器（半導體） |
Translated |
|
|
CNS 11898
1987 Edition Reliability Assured Plastic film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性M） |
|
|
|
CNS 4375
1987 Edition Butterfly Nuts 蝶形螺帽 |
|
|
|
CNS 5987
1987 Edition Shanks of Press Die 衝模柄 |
|
|
|
CNS 4366
1987 Edition Hexagon Bolts with Large Widths Across flats for Steel Structures (Joints with Hightensile, Prestressed Bolts) 六角頭螺栓（具大對面寬度、高預力連接鋼結構用） |
|
|
|
CNS 11895
1987 Edition General Rules for Reliability Assured Fixed Mica Capacitors 可靠度保證雲母固定電容器總則 |
|
|
|
CNS 5988
1987 Edition Stud Shanks for Press Dies 衝模用栓柄 |
|
|
|
CNS 7664
1987 Edition Method of Test for Low Frequency (Below 3 MHz)Electrical Connectors (TP - 25 Probe Damage Test) 頻率3 MHz以下電連接器檢驗法(探針損壞試驗TP-25) |
|
|
|
CNS 11941
1987 Edition General Rule for Electronic Scale with Price Indication 計價電子秤總則 |
Translated |
|
|
CNS 12070
1987 Edition Ejectorplate Guide Pin of Die Casting Molds 壓鑄模用頂出板導銷 |
|
|
|
CNS 12069
1987 Edition Ejector Rod of Die Casting Molds 壓鑄模用頂出桿 |
|
|
|
CNS 10874
1987 Edition Method of Test for Fiber Optic Devices ( FOTP-18 Acceleration ) 光纖裝置檢驗法（加速度試驗FOTP-18） |
|
|
|
CNS 12068
1987 Edition Support of Die Casting Molds 壓鑄模用支座 |
|
|
|
CNS 7642
1987 Edition Method of Test for Fiber Optic Devices (Air Leakage Testing of Fiber Optic Component Seals) 光纖裝置檢驗法(光纖組件密封漏氣試驗FOTP-23) |
|
|
|
CNS 11938
1987 Edition Sprue Puller of Molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 11939
1987 Edition Setting Plugs of Molds for Plastics 塑膠型模用定位塞 |
|
|
|
CNS 11812
1987 Edition Method of Test for Amplifiers 擴大機檢驗法 |
|
|
|
CNS 11999
1987 Edition Structural Steels with Specified Hardenability Bands 保證硬化能構造用鋼料（Ｈ鋼） |
|
|
|
CNS 11905
1987 Edition Method of Test for Fiber Optic Devices (FOTP-83 Cable to Interconnecting Device Axial Compressive Loading) 光纖裝置檢驗法（光纜至連接器之軸向壓力負載FOTP-83） |
|
|
|
CNS 8225
1987 Edition Method of Test for Dry Reed Switches (Quality Control and Quality Assurance Provisions) 乾式簧開關檢驗法（品質管制與品質保證規定） |
|
|
|
CNS 11993
1987 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-Launch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [396] [397] [398] [399] [400] [401] [402] |
