"f " CNS Standards List |
|
CNS 11835
1987 Edition Glossary of Terms Used in Heat Treatment of Iron and Steel 鋼鐵熱處理詞彙 |
|
|
|
CNS 11898
1987 Edition Reliability Assured Plastic film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性M） |
|
|
|
CNS 8226
1987 Edition Method of Test for Dry Reed Switches (Visual and Mechanical Inspection) 乾式簧開關檢驗法（目視與機械檢驗） |
|
|
|
CNS 8227
1987 Edition Method of Test for Dry Reed Switches (Operation Parameters) 乾式簧開關檢驗法（動作參數） |
|
|
|
CNS 8228
1987 Edition Method of Test for Dry Reed Switches (Dielectric) 乾式簧開關檢驗法（電介質） |
|
|
|
CNS 7661
1987 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connector (TP - 22 Life Test) 頻率3 MHz以下電連接器檢驗法（壽命試驗TP-22） |
|
|
|
CNS 8229
1987 Edition Method of Test For Dry Reed Switches (Operate, Bounce, Release and Transfer (SPDT) Time) 乾式簧開關檢驗法（動作、彈跳、復原與轉接時間） |
|
|
|
CNS 8230
1987 Edition Method of Test for Dry Reed Switches (Insulation Resistance) 乾式簧開關檢驗法（絕緣電阻） |
|
|
|
CNS 7643
1987 Edition Method of Test for Fiber Optic Devices (FOTP-34 Interconnection Devices Insertion Loss) 光纖裝置檢驗法(互接裝置插入損失FOTP-34) |
|
|
|
CNS 11935
1987 Edition Supporter of Molds for Plastics 塑膠型模用支持座 |
|
|
|
CNS 7663
1987 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 24 Maintenance Aging Test) 頻率3 MHz以下電連接器檢驗法(維護老化試驗TP-24) |
|
|
|
CNS 5993
1987 Edition Coil Springs for Press Dies 衝模用螺旋彈簧 |
|
|
|
CNS 5770
1987 Edition General Specification for Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 11893
1987 Edition Shears for Hedge Trimming 手剪（修剪樹籬用） |
|
|
|
CNS 10872
1987 Edition Method of Test for Fiber Optic Devices (FOTP-2 Impact Test) 光纖裝置檢驗法(撞擊試驗FOTP-2) |
|
|
|
CNS 10874
1987 Edition Method of Test for Fiber Optic Devices ( FOTP-18 Acceleration ) 光纖裝置檢驗法（加速度試驗FOTP-18） |
|
|
|
CNS 10875
1987 Edition Method of Test for Fiber Optic Devices ( FOTP-4 Temperature Life Test ) 光纖裝置檢驗法（溫度壽命試驗FOTP-4） |
|
|
|
CNS 11936
1987 Edition Stop Pins of Molds for Plastics 塑膠型模用止銷 |
|
|
|
CNS 11900
1987 Edition fixed Ceramic Capacitors for Electronic Equipment (Semiconductor) 電子設備用陶瓷固定電容器（半導體） |
Translated |
|
|
CNS 11934
1987 Edition Stop Bolts of Molds for plastics 塑膠型模用止動螺栓 |
|
|
|
CNS 11907
1987 Edition Method of Test for Fiber Optic Devices (FOTP-99 Gas Flame Test for Special Purpose Fiber Optic Cable) 光纖裝置檢驗法（特種用途光纜之火焰試驗FOTP-99） |
|
|
|
CNS 9231
1987 Edition Method of Test for Dry Reed Switches(Physical Dimensions) 乾式簧開關檢驗法（實體尺度） |
|
|
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for Plastics 塑膠型模用頂出套筒 |
|
|
|
CNS 11905
1987 Edition Method of Test for Fiber Optic Devices (FOTP-83 Cable to Interconnecting Device Axial Compressive Loading) 光纖裝置檢驗法（光纜至連接器之軸向壓力負載FOTP-83） |
|
|
|
CNS 11904
1987 Edition Method of Test for Fiber Optic Devices (FOTP-81 Compound Flow (Drip) Test for Filled Fiber Optic Cable) 光纖裝置檢驗法（有填充物光纜之化合物滴漏試驗FOTP-81） |
|
|
|
CNS 11902
1987 Edition Method of Test for Fiber Optic Devices (FOTP-52 Temperature Dependence of Attenuation for Optical Fibers) 光纖裝置檢驗法（溫度變化對光纖衰減之影響FOTP-52） |
|
|
|
CNS 11901
1987 Edition Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 8225
1987 Edition Method of Test for Dry Reed Switches (Quality Control and Quality Assurance Provisions) 乾式簧開關檢驗法（品質管制與品質保證規定） |
|
|
|
CNS 11933
1987 Edition Ejector Guide Pins of Molds for Plastics 塑膠型模用頂出導銷 |
|
|
|
CNS 8224
1987 Edition Method of Test for Dry Reed Switches (General Rules) 乾式簧開關檢驗法（總則） |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [395] [396] [397] [398] [399] [400] [401] |
