"f " CNS Standards List |
|
CNS 9146
1988 Edition 660V Single-Core, Twin-Core, Three-Core Silicon Rubber Insulated Lead Covered Metal Netting Covered Cable (660V-SSRLC, 660V-TSRLC) for Marine Use 船用660 V單心、二心、三心矽橡膠絕緣鉛皮被覆金屬網鎧裝電纜(660 V-SSRLC，660 V-DSRLC，660 V-TSRLC) |
|
|
|
CNS 8226
1987 Edition Method of Test for Dry Reed Switches (Visual and Mechanical Inspection) 乾式簧開關檢驗法（目視與機械檢驗） |
|
|
|
CNS 5993
1987 Edition Coil Springs for Press Dies 衝模用螺旋彈簧 |
|
|
|
CNS 5994
1987 Edition Ball Slide Die Sets for Press Dies 衝模用滾珠滑導模座組 |
|
|
|
CNS 8227
1987 Edition Method of Test for Dry Reed Switches (Operation Parameters) 乾式簧開關檢驗法（動作參數） |
|
|
|
CNS 4375
1987 Edition Butterfly Nuts 蝶形螺帽 |
|
|
|
CNS 8224
1987 Edition Method of Test for Dry Reed Switches (General Rules) 乾式簧開關檢驗法（總則） |
|
|
|
CNS 4366
1987 Edition Hexagon Bolts with Large Widths Across flats for Steel Structures (Joints with Hightensile, Prestressed Bolts) 六角頭螺栓（具大對面寬度、高預力連接鋼結構用） |
|
|
|
CNS 8225
1987 Edition Method of Test for Dry Reed Switches (Quality Control and Quality Assurance Provisions) 乾式簧開關檢驗法（品質管制與品質保證規定） |
|
|
|
CNS 8223
1987 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connector (TP - 41 Circular Jacket Cable Flexing Test) 頻率3 MHz以下電連接器檢驗法（圓形護套電纜可撓性試驗TP-41） |
|
|
|
CNS 11933
1987 Edition Ejector Guide Pins of Molds for Plastics 塑膠型模用頂出導銷 |
|
|
|
CNS 11934
1987 Edition Stop Bolts of Molds for plastics 塑膠型模用止動螺栓 |
|
|
|
CNS 8228
1987 Edition Method of Test for Dry Reed Switches (Dielectric) 乾式簧開關檢驗法（電介質） |
|
|
|
CNS 5992
1987 Edition Knockout Equipment for Press Dies 衝模用頂出裝置 |
|
|
|
CNS 5991
1987 Edition Round Punches for Press Dies 衝模用圓衝頭 |
|
|
|
CNS 8229
1987 Edition Method of Test For Dry Reed Switches (Operate, Bounce, Release and Transfer (SPDT) Time) 乾式簧開關檢驗法（動作、彈跳、復原與轉接時間） |
|
|
|
CNS 5990
1987 Edition Die Sets for Press Dies 衝模用模座組 |
|
|
|
CNS 11938
1987 Edition Sprue Puller of Molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 11935
1987 Edition Supporter of Molds for Plastics 塑膠型模用支持座 |
|
|
|
CNS 11936
1987 Edition Stop Pins of Molds for Plastics 塑膠型模用止銷 |
|
|
|
CNS 11937
1987 Edition Runner Pull Pins of Molds for Plastics 塑膠型模用流道拉銷 |
|
|
|
CNS 8222
1987 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connector (TP - 40 Crush Test) 頻率3 MHz以下電連接器檢驗法（軋壓試驗TP-40） |
|
|
|
CNS 5550
1987 Edition Method of Test for Thermistor 熱敏電阻器檢驗法 |
|
|
|
CNS 5987
1987 Edition Shanks of Press Die 衝模柄 |
|
|
|
CNS 5988
1987 Edition Stud Shanks for Press Dies 衝模用栓柄 |
|
|
|
CNS 8230
1987 Edition Method of Test for Dry Reed Switches (Insulation Resistance) 乾式簧開關檢驗法（絕緣電阻） |
|
|
|
CNS 11829
1987 Edition Light Emitting Diodes (for Indication) 發光二極體(指示用) |
|
|
|
CNS 11895
1987 Edition General Rules for Reliability Assured Fixed Mica Capacitors 可靠度保證雲母固定電容器總則 |
|
|
|
CNS 11874
1987 Edition fixed Mica Capacitors ( Type CM 35 ) 雲母固定電容器(CM35型) |
|
|
|
CNS 8667
1987 Edition Method of Test for Dry Reed Switches(Internal Moisture) 乾式簧開關檢驗法（內部潮濕） |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [393] [394] [395] [396] [397] [398] [399] |
