"o " CNS Standards List |
|
CNS 140
2017 Edition Wrench, Socket-Headed (Wrench Opening Ranging From 41 to 145 mm) 套筒扳手(口寬自41至145mm) |
![]() Translated |
|
|
CNS 11395
2017 Edition Method of Test for Stiffness of Paper and Paperboard(Taber Stiffness Tester) 紙及紙板剛度試驗法(Taber剛度試驗機) |
![]() Translated |
|
|
CNS 11937
2017 Edition Runner Pull Pins of Molds for Plastics 塑膠型模用流道拉銷 |
![]() |
|
|
CNS 4945
2017 Edition Adjusting Screws for Drawing Instruments 製圖儀器用調整螺釘 |
![]() |
|
|
CNS 9242
2017 Edition Method of Test for Low Frequency(Below 3 MHz) Electrical Connectors(TP - 42 Impact) 頻率3MHz以下電連接器檢驗法(碰撞試驗TP–42) |
![]() |
|
|
CNS 714
2017 Edition Cast Iron Flanged Gate Valves ( 5 kgf/㎠) ( Outside Screw Type) 鑄鐵凸緣型閘閥(5 kgf/㎠)(閥桿上升型) |
![]() |
|
|
CNS 4569
2017 Edition T-Head Bolts with One-Rounded Head T形頭螺栓(具單邊圓角) |
![]() |
|
|
CNS 14492-3
2017 Edition Methods of measurement on radio receivers for various classes of emission-Part3:Receivers for amplitude-modulated sound-broadcasting emissions 不同發射類別之無線電接收機的量測方法-第3部:調幅聲音廣播發射適用的接收機 |
![]() |
|
|
CNS 5663
2017 Edition Test Code for Accuracy of Three-Side Planers and Moulders 自動三面刨床精度檢驗標準 |
![]() |
|
|
CNS 13992
2017 Edition Fixed resistor networks in which not all resistors are individually measurable for use in electronic equipment 電子設備用不可單獨量測所有電阻元件之固定網路電阻器 |
![]() |
|
|
CNS 14270
2017 Edition 75 ohm type FD coaxial cable connector for cable television (CATV) 75ΩFD型有線電視同軸電纜連接器 |
![]() |
|
|
CNS 2148
2017 Edition Ferrosilicon 矽鐵 |
![]() Translated |
|
|
CNS 4654
2017 Edition Hexagon Set Screws with Full Dog Point 六角頭長柱端固定螺釘 |
![]() |
|
|
CNS 3418
2017 Edition Sasety Code for Power Press ( Safeguarding at the Point of Operation ) 動力壓機安全規章(工作點安全防護) |
![]() |
|
|
CNS 11763
2017 Edition Transistor Megaphones 電晶體喊話器 |
![]() |
|
|
CNS 11476
2017 Edition General Test Procedure of Failure Rate for Electronic Components 電子零組件故障率試驗法通則 |
![]() |
|
|
CNS 13782
2017 Edition Realiability Assured Infrared Emitting Diodes (IRED)(for Automation) 自動控制用可靠度保證紅外發光二極體 |
![]() |
|
|
CNS 6734
2017 Edition Disk Type Milling Cutters for Cutting Acme - Screw Threads for Threads with Included Angle of 30° 30°角愛克姆螺紋銑刀 |
![]() |
|
|
CNS 15091-13
2017 Edition Method of test for deep sea water - Determination of silicate 深層海水檢驗法-矽酸鹽之測定 |
![]() |
|
|
CNS 6351-1
2017 Edition oil of spearmint - Part 1: Native type (Mentha spicata L.) 綠薄荷油-第1部:原生型 |
![]() |
|
|
CNS 9723
2017 Edition Dimensions of Pallets for Machining Centers 切削中心機用托板之尺度 |
![]() |
|
|
CNS 5972
2017 Edition Cast Iron Flanged Globe Valves (10kgf/c㎡) 鑄鐵凸緣型球型閥(10 kgf/㎠) |
![]() Translated |
|
|
CNS 2938
2017 Edition Pearlitic Malleable Iron Castings 波來體展性鑄鐵件 |
![]() |
|
|
CNS 6890
2017 Edition AC Solenoids for General Purpose 一般用交流電磁圈 |
![]() |
|
|
CNS 2609
2017 Edition Corrugated Aluminium Sheets 波形鋁片 |
![]() Translated |
|
|
CNS 4267
2017 Edition Single Point Carbide Tipped Tools 焊接碳化物車刀 |
![]() Translated |
|
|
CNS 11028
2017 Edition Method of test for milk and milk products - Determination of scorched particles 乳品檢驗法-乳粉焦粒之測定 |
![]() |
|
|
CNS 8672
2017 Edition Method of Test for Dry Reed Switches(Carry Current) 乾式簧開關檢驗法(負載電流) |
![]() |
|
|
CNS 505
2017 Edition ISo Metric Fine Screw Threads (Diameters from 42 to 300 mm and Pitch 4 mm) 公制細螺紋8(ISO制)(標稱直徑42至300公釐,螺距4公釐) |
![]() |
|
|
CNS 11381-2
2017 Edition Glossary of Terms for Reliability (Terms of Maintainability) 可靠度詞彙(有關維護度之詞彙) |
![]() |
Find out:15086Items | To Page of: First -Previous-Next -Last | [357] [358] [359] [360] [361] [362] [363] |