"P V " CNS Standards List |
|
CNS 14432-2
2019 Edition Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions − Method by analysis of evolved carbon dioxide − Part 2: Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test 塑膠材料在控制堆肥條件下最終好氧生物分解度測定法－二氧化碳釋出量分析法－第2部：實驗室規模重量測定法 |
|
|
|
CNS 15251-3
2019 Edition Information technology − Open document format for office applications (OpenDocument) v1.2 − Part 3: Packages 資訊技術－辦公室應用軟體OpenDocument v1.2 之開放文件格式－第3部：套件 |
|
|
|
CNS 30
2019 Edition Belt drives − Pulleys − Quality, finish and balance 皮帶傳動－皮帶輪－品質、加工及平衡 |
|
|
|
CNS 13181-2
2019 Edition The Method of Test of Presure Regulator and Vaporizers for LGP Automobile Fuel Systems 液化石油氣汽車燃氣系統–壓力調整器與氣化器檢驗法 |
Translated |
|
|
CNS 15755-5-6
2019 Edition Conversion tables for units − Part 5-6: Pressure or stress − Megapascal and kilogram-force per square centimeter 單位換算表－第5-6 部：壓力或應力－百萬帕斯卡與公斤力每平方公分 |
|
|
|
CNS 11067
2019 Edition Carbon and Alloy Steel Forgings for Pressure Vessels for Low Temperature Service 低溫壓力容器用碳鋼及合金鋼鍛鋼件 |
|
|
|
CNS 1475
2019 Edition Viscose Rayon Spun Yarns, Cotton System, Unfinished 黏液嫘縈棉紗（棉紡式，本白紗） |
Translated |
|
|
CNS 15659-1
2019 Edition Evaluation of moisture-absorbing and quick-drying properties in textiles Part 1: Combination test 紡織品吸濕速乾性能評估－第1 部：組合試驗法 |
|
|
|
CNS 10273-4
2019 Edition Rubber, unvulcanized − Determinations using a shearing-disc viscometer − Part 4: Determination of the Mooney stress-relaxation rate 未硫化橡膠－使用剪力-圓盤型黏度計－第4 部:木尼應力-鬆弛速率之測定 |
|
|
|
CNS 8110
2019 Edition Marine Forged Steel Globe Valves for Compressed Air 船用鍛鋼壓縮空氣球形閥 |
|
|
|
CNS 14934-5
2019 Edition Electromagnetic compatibility (EMC) - Limits - Part 5: Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16A 電磁相容－限制值－第5部：額定電流大於16 A之設備於低電壓電源系統中電壓變動及閃爍之限制值 |
|
|
|
CNS 15449-2-101
2019 Edition Safe requirements for electrical for measurement, control and laboratory use ? Part 2-101: Particular requirements for in vitro diagnostic (IVD) medical equipment 量測、控制及實驗室使用電氣設備安全規定－第2-101 部:體外診斷(IVD)醫用設備之個別規定 |
|
|
|
CNS 15721
2019 Edition Self adhesive tapes – Determination of peel adhesion properties 感壓性黏膠帶－剝離黏著力測定法 |
|
|
|
CNS 11391
2019 Edition Decorative electroplated coatings of copper/nickel/chromium on plastics 塑膠裝飾用之銅鎳鉻電鍍層 |
|
|
|
CNS 16083-2
2019 Edition Viscosity and viscometric fixed points of glass − Part 2: Determination of annealing point and strain point by fiber elongation 玻璃黏度和黏度固定點－第2部：以玻璃絲拉伸法測定退火點和應變點 |
|
|
|
CNS 11064
2019 Edition Injection Nozzle Holder Type P for Road Vehicles (with Body and with Fixing FLats) 汽車用Ｐ型燃料噴油嘴固定器 |
|
|
|
CNS 15725
2019 Edition Belt drives − Pulleys for V-belts (system based on datum width) − Geometrical inspection of grooves 皮帶傳動－使用三角皮帶之皮帶輪(以基準寬度為基礎之系統)－溝槽之幾何檢驗 |
|
|
|
CNS 5812
2019 Edition Methods of Test for Peel Strength of Adhesives 黏著劑之剝離強度測定法 |
|
|
|
CNS 5846-1
2019 Edition Plastics - Determination of ash - Part 5: Poly (vinyl chloride) 塑膠－沙丕(Charpy)衝擊性能測定法－第1部：非儀器式衝擊試驗 |
|
|
|
CNS 14937
2019 Edition Method of test for effects of heat and air on asphaltic materials (Thin-film oven test) 柏油材料受熱及空氣影響試驗法（薄膜烘箱法） |
|
|
|
CNS 14118
2019 Edition Emergency shut-off valves for nature gas with high pressure and intermediate pressure 高、中壓天然氣用緊急遮斷閥 |
|
|
|
CNS 20349-1
2019 Edition Personal protective equipment − Footwear protecting against risks in foundries and welding − Part 1: Requirements and test methods for protection against risks in foundries 個人防護具－防止鑄造及熔接中風險之鞋類－第1部：防護鑄造中風險之要求事項及試驗方法 |
|
|
|
CNS 14498-2
2019 Edition Road vehicles - Electrical disturbances from conduction and coupling - Part 2: Electrical transient conduction along supply lines only 道路車輛－經由傳導及耦合之電擾動－第２部：僅由電源線傳導之電暫態 |
|
|
|
CNS 15176-26-1
2019 Edition Wind turbines − Part 26-1: Time-based availability for wind turbine generating systems 風力機－第26-1 部：風力發電機系統以時間為基礎之可利用率 |
|
|
|
CNS 697
2019 Edition Activated Carbon Powder for Industrial Use 工業用活性碳（粉狀） |
|
|
|
CNS 29182-1
2019 Edition Information technology − Sensor networks: Sensor Network Reference Architecture (SNRA) − Part 1: General overview and requirements 資訊技術－感測器網路：感測器網路參考架構(SNRA)－第1部：概觀及要求事項 |
|
|
|
CNS 7529
2019 Edition Method for sampling of abrasive grains 磨料採樣法 |
|
|
|
CNS 8434
2019 Edition Textiles − Tests for colour fastness − Colour fastness to drycleaning using perchloroethylene solvent 紡織品－色牢度試驗法－耐四氯乙烯溶劑乾洗色牢度 |
|
|
|
CNS 15755-5-9
2019 Edition Conversion tables for units − Part 5-9: Pressure or stress − Megapascal and standard atmosphere 單位換算表－第5-9 部：壓力或應力－百萬帕斯卡與標準大氣壓 |
|
|
|
CNS 12544
2019 Edition Mechanical vibration and shock − Hand-arm vibration − Measurement and evaluation of the vibration transmissibility of gloves at palm of the hand 機械性振動及衝擊－手臂振動－在手套之手掌處的振動傳導率之量測及評估 |
|
| Find out:3530Items | To Page of: First -Previous-Next -Last | [31] [32] [33] [34] [35] [36] [37] |
