"D C " CNS Standards List |
|
CNS 14005
2021 Edition Environmental management systems − Guidelines for a flexible approach to phased implementation 環境管理系統－分階段實施之彈性方法指導綱要 |
|
|
|
CNS 3007
2021 Edition Adapter Sleeves with Nut and Retainer for Ball and Roller Bearings 接頭斜套（含螺帽和保險鎖用於輾滾軸承者） |
|
|
|
CNS 8758
2021 Edition Method of Test for Theoretical Maximum Specific Gravity of Bituminous Paving Mixtures 瀝青舖面混合料理論最大比重試驗法 |
|
|
|
CNS 15693-23
2021 Edition Conduit systems for cable management − Part 23: Particular requirements − Flexible conduit systems 電纜管理用導線管系統－第23 部：特定要求－可撓式導線管系統 |
|
|
|
CNS 15841
2021 Edition Oil of lime expressed, Persian type (Citrus latifolia Tanaka) 萊姆油(壓榨法，波斯型) |
|
|
|
CNS 13802-6
2021 Edition Graphical Symbols for Diagrams (Production anD Conversion of Electrical Energy) 電機工程製圖符號（電能之產生及轉換） |
|
|
|
CNS 4291
2021 Edition Pressure sensitive adhesive polyvinyl chloride tapes for corrosion protection 包裝用感壓性聚氯乙烯黏膠帶 |
|
|
|
CNS 2293
2021 Edition Leucaena whole plant meal (for feeding) 銀合歡粉（飼料用） |
Translated |
|
|
CNS 15784-1
2021 Edition Low-voltage electrical installations − Part 1: Fundamental principles, assessment of general characteristics, definitions 低電壓電機裝備－第1 部：基本原則、一般特性之評估及定義 |
|
|
|
CNS 12670
2021 Edition Methods of post weld heat treatment 銲後熱處理法 |
|
|
|
CNS 8754
2021 Edition Methods of Noise Spectrum Measurement for Fans, Blowers anD Compressors 風扇、鼓風機、壓縮機、噪音譜測定法 |
|
|
|
CNS 9662
2021 Edition Method of Test for Air Content of Freshly MixeD Concrete by the Volumetric Method 新拌混凝土空氣含量試驗法（容積法） |
|
|
|
CNS 10026
2021 Edition Flame resistant conveyor belts − Classification and test method 耐燃輸送帶－級別及試驗方法 |
|
|
|
CNS 10210
2021 Edition Method of Test for Gaskets for Windows, Doors and Joints of Panel in Buildings 建築用墊條檢驗法 |
|
|
|
CNS 7339
2021 Edition Round Head Rivets Nominal Diameters 1 to 8 mm 圓頭鉚釘，標稱直徑１至８ｍｍ |
|
|
|
CNS 13454
2021 Edition Glassfiber Reinforced Plastic Underground petroleum Pipes and Fittings 玻璃纖維強化塑膠地下油管及配件 |
Translated |
|
|
CNS 9062
2021 Edition Pedestal Plain Bearings Assembly, Housing 托架滑動軸承–總成及外殼 |
|
|
|
CNS 9405
2021 Edition Method of Test for Abrasion Resistance of Coatings of Paint, Varnish, Lacquer, and Related Products with the Air Blast Abrasion Tester 油漆、凡立水、噴漆及有關產品磨耗抗力檢驗法（鼓風磨耗試驗法） |
|
|
|
CNS 11942-3
2021 Edition Methods for determination of lead in copper anD Copper alloys 銅及銅合金中鉛定量法 |
|
|
|
CNS 14572
2021 Edition Corrugated polyethylene pipe 聚乙烯波紋管 |
|
|
|
CNS 15448-1
2021 Edition Ophthalmic optics - Uncut finished spectacle lenses - Part 1: Specifications for single-vision and multifocal lenses 眼科光學－未切邊之眼鏡鏡片成品－第1部：單光與多焦點眼鏡鏡片規格 |
|
|
|
CNS 13333-2
2021 Edition Plastics − Methods for determining the density of non-cellular plastics − Part 1: Immersion method, liquid pyknometer method and titration method 塑膠－非發泡塑膠之密度測定法－第2 部：密度梯度管柱法 |
|
|
|
CNS 15918-3
2021 Edition Thermoplastics pipes − Determination of tensile properties − Part 3: Polyolefin pipes 熱塑性塑膠管－抗拉性能測定－第3 部：聚烯烴管 |
|
|
|
CNS 8337
2021 Edition Pressure sensitive adhesive polypropylene tapes for packaging 防蝕用感壓性聚氯乙烯黏膠帶 |
|
|
|
CNS 3642
2021 Edition Method of test for edible oils and fats－Determination of moisture and volatile matter 食用油脂檢驗法－水分及揮發物之測定 |
|
|
|
CNS 13802-7
2021 Edition Graphical Symbols for Diagrams (Switchgear,Controlgear and Protective Devices) 電機工程製圖符號（開關設備、控制設備及保護設備） |
|
|
|
CNS 15468-2
2021 Edition Fuel cell technologies − Part 2: Fuel cell modules 燃料電池技術－第2 部：燃料電池模組 |
|
|
|
CNS 1144
2021 Edition Method of Test for Insulated Rubber Tape 絕緣橡膠布帶檢驗法 |
Translated |
|
|
CNS 7216
2021 Edition Grain-oriented magnetic steel sheet and strip 方向性電磁鋼片及鋼帶 |
|
|
|
CNS 15256
2021 Edition Acoustics – Laboratory measurement procedures for ducted silencers and air-terminal units – Insertion loss, flow noise and total pressure loss 聲學－風管消音箱及空氣終端單元之實驗室量測程序－插入損失、氣流噪音及總壓力損失 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [31] [32] [33] [34] [35] [36] [37] |
