"a " CNS Standards List |
|
CNS 13507
2017 Edition Methods of Test for Glass - Fibor - Reinferced Plastic Pipe Fittings 玻璃纖維強化塑膠管配件檢驗法 |
![]() Translated |
|
|
CNS 5774
2017 Edition Thermistor Rods, Insulated (Style TRC) 管形絕緣熱敏電阻器(型號TRC) |
![]() |
|
|
CNS 3714
2017 Edition Hand-Supported Hair Dryers 手提型頭髮吹風機 |
![]() Translated |
|
|
CNS 4356
2017 Edition Slotted Pan Head Screws with Large Head 有槽大盤頭螺釘 |
![]() Translated |
|
|
CNS 3422
2017 Edition Oil-resistant Cork Sheet 耐油軟木板 |
![]() |
|
|
CNS 15091-17
2017 Edition Method of test for deep sea water - Determination of total organic carbon 深層海水檢驗法-總有機碳之測定 |
![]() |
|
|
CNS 4700
2017 Edition Hexagon Head Bolts with Thread Approximately to Head and with Small Widths Across Flats 六角頭全螺紋螺栓(具小對面寬度) |
![]() |
|
|
CNS 13198
2017 Edition Fixed Multilayer Ceramic Chip Capacitors for Use in Electronic Equipment 電子設備用固定多層陶瓷晶片電容器 |
![]() |
|
|
CNS 8219
2017 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 29 Contact Retention Test ) 頻率3MHz以下電連接器檢驗法(接點之牢固試驗TP–29) |
![]() |
|
|
CNS 13544
2017 Edition Frequency Weighting for the Measurement of Aircraft Noise (D-Weighting) 量測航空噪音的頻率加權–D加權 |
![]() |
|
|
CNS 209
2017 Edition Long Drills with Square Taper Shank 方錐柄長鑽頭 |
![]() Translated |
|
|
CNS 9097
2017 Edition Thermostats ( Pressure Type ) 恆溫器(壓力式) |
![]() |
|
|
CNS 13556
2017 Edition Method of Test for Flexural Properties of Carbon Fiber Reinforced Plastics 碳纖維強化塑膠抗曲性能試驗法 |
![]() Translated |
|
|
CNS 12743
2017 Edition Butterfly Valves for Water Works (Wafer Type) 水道用蝶型閥(薄體型) |
![]() Translated |
|
|
CNS 12072
2017 Edition Locating Pin of Die Casting Molds 壓鑄模用定位銷 |
![]() |
|
|
CNS 1110
2017 Edition Method of Test for Hand Saws for Carpenter 木工用手鋸檢驗法 |
![]() |
|
|
CNS 10726
2017 Edition Method of Test for Printing Ink Permeation of Paper (Castor Oil Test) 紙張之印刷油墨滲透性試驗法(蓖麻油法) |
![]() Translated |
|
|
CNS 783-6
2017 Edition Sodium carbonate for industrial use - Part 6 : Determination of matter insoluble in water at 50℃ 工業用碳酸鈉-第6部:50℃水不溶物測定法 |
![]() |
|
|
CNS 13059-6
2017 Edition Photovoltaic devices Par 6:Requirements for reference solar modules 光電伏打元件(第六部:基準太陽電池模組之要求) |
![]() |
|
|
CNS 11933
2017 Edition Ejector Guide Pins of Molds for Plastics 塑膠型模用頂出導銷 |
![]() |
|
|
CNS 4479
2017 Edition Hexagon Socket Set Screws with Full Dog Point 六角承窩無頭長柱端固定螺釘 |
![]() Translated |
|
|
CNS 7166
2017 Edition Method of Test for Color after Heating of Fatty Acids 脂肪酸加熱後之顏色檢驗法 |
![]() |
|
|
CNS 575
2017 Edition Steel bars for rivets 鉚釘用鋼棒 |
![]() |
|
|
CNS 12362
2017 Edition Method of Test for Fiber Optic Devices ( FOTP-91 Fiber Optic Cable Twist-Bend Test) 光纖裝置檢驗法(光纜扭與彎試驗FOTP–91) |
![]() |
|
|
CNS 13653
2017 Edition Lot-Control Testing for Light Emitting Diode(for Communication) 通信用發光二極體之批品質控制測試 |
![]() |
|
|
CNS 9359-17
2017 Edition Information technology - Vocabulary - Part 17: Databases 資訊技術-詞彙-第17部:資料庫 |
![]() |
|
|
CNS 4149
2017 Edition Canned chinese foods 中式食品罐頭 |
![]() |
|
|
CNS 14139
2017 Edition Measurement methods for the performance of transmitter and receiver modules used for wireless infrared communication 無線通信用紅外線傳輸和接收模組功能特性量測法 |
![]() |
|
|
CNS 14672
2017 Edition Methods of measurement of the suppression characteristics of passive radio interference filters and suppression components 被動式射頻干擾濾波器和抑制元件特性之量測方法 |
![]() |
|
|
CNS 12851
2017 Edition Nodular Graphite Iron Screwed Lift Check Valves (10 kgf/㎠) 球狀石墨鑄鐵螺紋口升降型止回閥(10 kgf/㎠) |
![]() Translated |
Find out:15242Items | To Page of: First -Previous-Next -Last | [348] [349] [350] [351] [352] [353] [354] |