"or " CNS Standards List |
|
CNS 5267
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Cumulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 10911
1984 Edition Method of Test for Microswitches 微動開關試驗法 |
|
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 6410
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
|
|
CNS 6414
1984 Edition Basic Rack of Straight Bevel Gears for General and Heavy Engineering 直齒傘齒輪之基準齒條(一般機械及重機械用) |
|
|
|
CNS 2900
1984 Edition Polyvinyl Chloride Insulated Copper Wire 聚氯乙烯絕緣屋內電話線 |
Translated |
|
|
CNS 4663
1984 Edition Closed Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽（片封式，嵌於塑膠製品內） |
|
|
|
CNS 6409
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Material Factor Zм 圓柱齒輪與傘齒輪之負載能力計算－材料因數ＺM |
|
|
|
CNS 4664
1984 Edition Closed Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽（封閉式，嵌於塑膠製品內） |
Translated |
|
|
CNS 7344
1984 Edition Crowbars (for Fire Fighting Use) 撬桿（消防用） |
|
|
|
CNS 6411
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics Mouldings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 6407
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算－負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 4731
1984 Edition Knurled Nuts for Drawing Instruments 滾紋螺帽（製圖儀器用） |
|
|
|
CNS 6415
1984 Edition Series of modules for Straight Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 6412
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 6408
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算－齒廓面作用帶因數Ｚ H |
|
|
|
CNS 5059
1983 Edition Supporting Pin and Locating Pin 支座銷與定位銷 |
|
|
|
CNS 10726
1983 Edition Method of Test for Printing Ink Permeation of Paper (Castor Oil Test) 紙張之印刷油墨滲透性試驗法（蓖麻油法） |
Translated |
|
|
CNS 9475
1983 Edition Test Code for Performance of Numerically Controlled Turret and Single Spindle Drilling Machines with Vertical Spindle 數值控制立式六角及單軸鑽床動態檢驗法 |
|
|
|
CNS 5057
1983 Edition Feet with Thread for Jigs and Fixtures 具螺紋柄支腳（夾具用） |
|
|
|
CNS 4584
1983 Edition Bolted Connrctions with Reduced Body; Thread Holes for Studs 減徑柄螺栓之結合法－螺樁之旋入螺孔 |
|
|
|
CNS 4607
1983 Edition Studs for T-Nuts 螺樁（Ｔ形螺帽用） |
|
|
|
CNS 4107
1983 Edition Flat Seal for Hydraulic Couplings 液壓接頭用扁封 |
|
|
|
CNS 10639
1983 Edition Polymer Dispersions for Cement Nodifier 水泥混和用聚合物擴散材料 |
|
|
|
CNS 4646
1983 Edition Square Taper Washers for High Prestressed I-Sections 斜墊圈（工字鐵高強度結構用） |
|
|
|
CNS 168
1983 Edition Tangential Key for Impact Type Reversal Load 切線鍵（用於衝擊式之變向負荷） |
|
|
|
CNS 170
1983 Edition Flat Fitting Keys (for Thin Hub) 配合平鍵（用於薄轂） |
|
|
|
CNS 171
1983 Edition Screw and Hole for Sliding Key 滑鍵螺釘及孔 |
|
| Find out:10886Items | To Page of: First -Previous-Next -Last | [344] [345] [346] [347] [348] [349] [350] |
