"a " CNS Standards List |
|
CNS 9796
2017 Edition Saddle supported horizontal pressure vessels 以鞍座支撐之臥型壓力容器 |
|
|
|
CNS 4662
2017 Edition Open Insert Nuts for Plastics Mouldings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 4664
2017 Edition Closed Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽（封閉式，嵌於塑膠製品內） |
Translated |
|
|
CNS 3882
2017 Edition Coating for Bicycle Parts 自行車（腳踏車）零件塗裝 |
Translated |
|
|
CNS 9110
2017 Edition Symbols of Bus - Bar of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖滙流排槽類符號 |
|
|
|
CNS 10643
2017 Edition Curved Lip, Fluted Jaw, Blacksmiths Tongs 鍛工用有槽顎夾夾鉗 |
|
|
|
CNS 12253
2017 Edition Quartz Crystal Units For Oscillators (For 1 MHz -- 125 MHz) 振盪器用石英振盪晶體（１ＭＨｚ～１２５ＭＨｚ用） |
|
|
|
CNS 501
2017 Edition ISO Metric Fine Screw Threads (Diameters From 8 to 30mm and Pitches 1 to 1.25mm) 公制細螺紋4（ISO制）（標稱直徑8至30公釐，螺距1至1.25公釐） |
|
|
|
CNS 3607
2017 Edition Single angle Milling Cutters with Threaded Holes 附螺紋孔單側角銑刀 |
Translated |
|
|
CNS 13126
2017 Edition Metallic and Other Non-2organic Coatings -General Rules for Corrosion Tests Applicablc for Storage Conditionss 金屬和無機被覆–儲存狀態下之腐蝕試驗通則 |
|
|
|
CNS 3314
2017 Edition Canned bean sprout 豆芽菜罐頭 |
|
|
|
CNS 10693
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Definition and Test Condition) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（定義、試驗條件） |
|
|
|
CNS 1188
2017 Edition Flat File for Carpenter, Sharp Flat End 木工用尖平頭扁平銼 |
Translated |
|
|
CNS 15524-4
2017 Edition Plastics - Determination of ash - Part 3: Unplasticized cellulose acetate 塑膠－灰分測定法－第4部：聚醯胺 |
|
|
|
CNS 8188
2017 Edition Method of Test for Water Retention by Concrete Curing Materials 混凝土養護材料保持水份能力檢驗法 |
|
|
|
CNS 5962
2017 Edition Bronze Screwed Globe Valves (5kgf/c㎡) 青銅螺紋口球形閥（5 kgf/㎠） |
|
|
|
CNS 8902
2017 Edition Method of Test for Oil Based Caulking Compounds for Building 建築用油性填縫材料檢驗法 |
|
|
|
CNS 60227-1
2017 Edition Polyvinyl chloride insulated cables of rated voltages up to and including 450/750V − Part 1: General requirements 額定電壓450/750 V以下聚氯乙烯絕緣電纜－第1 部：一般要求 |
|
|
|
CNS 16002
2017 Edition Rubber compounding ingredients − Carbon black − Determination of specific surface area by nitrogen adsorption method − Single-point procedures 橡膠配合劑－碳黑－比表面積之氮吸附測定－單點程序 |
|
|
|
CNS 14489
2017 Edition Manipulating industrial robots-Presentation of characteristics 工業用機器人-特性之標示 |
|
|
|
CNS 3373
2017 Edition Straight Shank Drills 直柄鑽頭 |
Translated |
|
|
CNS 13007
2017 Edition MaG Welding Flux Cored Wire for Molybdenum Steel and Chrominum Molybdenum Steel 鉬鋼及鉻鉬鋼ＭＡＧ熔接用空心填入熔劑鋼線 |
|
|
|
CNS 3330
2017 Edition Small Type Lead Storage Batteries for Motorcycles 機車用鉛蓄電池 |
Translated |
|
|
CNS 7285
2017 Edition Method for Determination of Gold and Silver in Ores with Tellurium 含碲礦中金及銀定量法 |
|
|
|
CNS 4895
2017 Edition accuracy Inspection of Hack Sawing Machines 弓鋸機精度檢驗標準 |
Translated |
|
|
CNS 2075
2017 Edition Method of Test for aluminium Sulfate( for Water Works ) 硫酸鋁（自來水淨化用）檢驗法 |
Translated |
|
|
CNS 4412
2017 Edition Slotted Countersunk (Flat) Head Screws with Full Dog Point 有槽平頂埋頭長柱端螺釘 |
|
|
|
CNS 13164
2017 Edition Method of Tension Shear Test for Spot Welded Joints 點熔接接合之拉剪試驗法 |
|
|
|
CNS 128
2017 Edition Metric Taper Gauge, Without Flat Head 公制圓錐量規（無扁頭） |
|
|
|
CNS 4708
2017 Edition Plastic drinking straw 直流用塑膠膜電容器（特牲Ｍ） |
Translated |
| Find out:15242Items | To Page of: First -Previous-Next -Last | [338] [339] [340] [341] [342] [343] [344] |
