"P " CNS Standards List |
|
CNS 9369
1988 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 35 Proposed Insert Retention) 頻率3 MHz以下電連接器檢驗法（接觸端子插入扣鎖TP-35） |
|
|
|
CNS 9367
1988 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 14 Ozone Exposure) 頻率3 MHz以下電連接器檢驗法（耐臭氧試驗TP-14） |
|
|
|
CNS 5770
1987 Edition General SPecification for Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 10607
1987 Edition Hair Curling APpliances 鬈髮器 |
Translated |
|
|
CNS 4079
1987 Edition Wire SPring Relay 線簧電驛 |
|
|
|
CNS 5535
1987 Edition Small Switch for Single-Phase Motors 單相電動機用小型開關 |
Translated |
|
|
CNS 9105
1987 Edition Symbols of Electric machines of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電機類符號 |
|
|
|
CNS 2662
1987 Edition Electric Percolators 電咖啡壺 |
Translated |
|
|
CNS 5988
1987 Edition Stud Shanks for Press Dies 衝模用栓柄 |
|
|
|
CNS 5990
1987 Edition Die Sets for Press Dies 衝模用模座組 |
|
|
|
CNS 5991
1987 Edition Round Punches for Press Dies 衝模用圓衝頭 |
|
|
|
CNS 5992
1987 Edition Knockout EquiPment for Press Dies 衝模用頂出裝置 |
|
|
|
CNS 5993
1987 Edition Coil SPrings for Press Dies 衝模用螺旋彈簧 |
|
|
|
CNS 5994
1987 Edition Ball Slide Die Sets for Press Dies 衝模用滾珠滑導模座組 |
|
|
|
CNS 6032
1987 Edition Alkaline Primary Cells and Batteries 鹼性一次電池 |
|
|
|
CNS 5987
1987 Edition Shanks of Press Die 衝模柄 |
|
|
|
CNS 11901
1987 Edition Dimensions of Racks and Unit Chassis of Electronic EquiPment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 11939
1987 Edition Setting Plugs of Molds for Plastics 塑膠型模用定位塞 |
|
|
|
CNS 11938
1987 Edition SPrue Puller of Molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 11937
1987 Edition Runner Pull Pins of Molds for Plastics 塑膠型模用流道拉銷 |
|
|
|
CNS 11936
1987 Edition StoP Pins of Molds for Plastics 塑膠型模用止銷 |
|
|
|
CNS 11935
1987 Edition SuPporter of Molds for Plastics 塑膠型模用支持座 |
|
|
|
CNS 11934
1987 Edition StoP Bolts of Molds for plastics 塑膠型模用止動螺栓 |
|
|
|
CNS 11933
1987 Edition Ejector Guide Pins of Molds for Plastics 塑膠型模用頂出導銷 |
|
|
|
CNS 11932
1987 Edition Angle Pins of Molds for Plastics 塑膠型模用角銷 |
|
|
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for Plastics 塑膠型模用頂出套筒 |
|
|
|
CNS 11907
1987 Edition Method of Test for Fiber OPtic Devices (FOTP-99 Gas Flame Test for Special Purpose Fiber Optic Cable) 光纖裝置檢驗法（特種用途光纜之火焰試驗FOTP-99） |
|
|
|
CNS 11906
1987 Edition Method of Test for Fiber OPtic Devices (FOTP-84 Jacket Self-Adhesion (Blocking) Test for Fiber Optic Cable) 光纖裝置檢驗法（光纜被覆自黏性試驗FOTP-84） |
|
|
|
CNS 11905
1987 Edition Method of Test for Fiber OPtic Devices (FOTP-83 Cable to Interconnecting Device Axial Compressive Loading) 光纖裝置檢驗法（光纜至連接器之軸向壓力負載FOTP-83） |
|
|
|
CNS 7642
1987 Edition Method of Test for Fiber OPtic Devices (Air Leakage Testing of Fiber Optic Component Seals) 光纖裝置檢驗法(光纖組件密封漏氣試驗FOTP-23) |
|
| Find out:11004Items | To Page of: First -Previous-Next -Last | [338] [339] [340] [341] [342] [343] [344] |
