"a, " CNS Standards List |
|
CNS 9112
2017 Edition Symbols of Telephone and Bell of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電話、電鈴類符號 |
|
|
|
CNS 3510
2017 Edition Copper and copper alloy covered electrodes 銅及銅合金被覆銲條 |
|
|
|
CNS 4849
2017 Edition Core Plugs, Core Plug Bars 心塞、心塞桿 |
|
|
|
CNS 4584
2017 Edition Bolted Connrctions with Reduced Body; Thread Holes for Studs 減徑柄螺栓之結合法–螺樁之旋入螺孔 |
|
|
|
CNS 12849
2017 Edition Nodular Graphite Iron Flanged Globe Valves (10 kgf/㎠) 球狀石墨鑄鐵凸緣球形閥（10 kgf/㎠） |
Translated |
|
|
CNS 8219
2017 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 29 Contact Retention Test ) 頻率３ＭＨｚ以下電連接器檢驗法（接點之牢固試驗ＴＰ–２９） |
|
|
|
CNS 10978
2017 Edition Aerosol type mini fire extinguish 噴霧式迷你型滅火器 |
|
|
|
CNS 15422
2017 Edition Office furniture - Storage cabinets 辦公室用收納單元 |
|
|
|
CNS 12560
2017 Edition Method of Test for Fiber Optic Devices (FOTP-100 Gas Leakage Test for Gas-Blocked Fiber Optic Cables) 光纖裝置檢驗法（氣密光纜之漏氣試驗ＦＯＴＰ–１００） |
|
|
|
CNS 15991
2017 Edition Method of test for iron staining materials in lightweight concrete aggregates 輕質混凝土粒料中含鐵污染材料試驗法 |
|
|
|
CNS 14677-7
2017 Edition Sound system equipment Part 7: Headphone and earphones 聲音系統設備－第７部：頭戴式耳機及耳塞式耳機 |
|
|
|
CNS 5996
2017 Edition Guide Pins of Dies for Die Casting 壓鑄模用導銷 |
|
|
|
CNS 6399
2017 Edition Dental Wrought Gold - Silver - Palladium Alloy 牙科用鍛造金銀鈀合金 |
|
|
|
CNS 60227-1
2017 Edition Polyvinyl chloride insulated cables of rated voltages up to and including 450/750V − Part 1: General requirements 額定電壓450/750 V以下聚氯乙烯絕緣電纜－第1 部：一般要求 |
|
|
|
CNS 5501
2017 Edition Self - Aligning Ball Bearings: Wide Inner Race, Inner Race with Clamping Sleeve 自動對位滾珠軸承（具加寬內環及附夾緊套筒內環） |
|
|
|
CNS 6628
2017 Edition Finger Sack for Medical Use 醫療用指套 |
|
|
|
CNS 4364
2017 Edition Hexagon Head Fitting Bolts with Long Threaded Portion 六角頭配合螺栓（具長螺紋部份） |
|
|
|
CNS 12981
2017 Edition Method of test for milk and milk products - Determination of fat content in edible cheese 乳品檢驗法－食用乾酪脂肪含量之測定 |
|
|
|
CNS 14623-1
2017 Edition Sterilization of health care products-chemical indicators-Part 1：General requirements 保健產品之滅菌─化學指示劑─第一部分：一般規定 |
|
|
|
CNS 12722
2017 Edition Method of Test for U-Shaped High Density Polyethylene Bag 高密度聚乙烯背心袋檢驗法 |
Translated |
|
|
CNS 12816-1
2017 Edition Helical-scan video tape cassette system using 12.65mm(0.5in)magnetic tape on type VHS-Part1:VHS video cassette system ＶＨＳ方式１２．６５ｍｍ（０．５ｉｎ）磁帶螺線掃描影像卡式磁帶系統-第1部:VHS及C-VHS影像磁帶系統 |
|
|
|
CNS 13544
2017 Edition Frequency Weighting for the Measurement of Aircraft Noise (D-Weighting) 量測航空噪音的頻率加權–Ｄ加權 |
|
|
|
CNS 1109
2017 Edition Two-man Saws 雙人用長鋸 |
Translated |
|
|
CNS 15832-2-2
2017 Edition Method of test for coating components − Part 2-2: Component analysis in solvent soluble matter − Softening point (Ring-and-ball method) 塗料成分試驗法－第2-2部：溶劑可溶物中成分分析－軟化點(環與球法) |
|
|
|
CNS 2057
2017 Edition Power Thrasher 耕耘機〔動力15仟瓦（20馬力）以下〕 |
|
|
|
CNS 4647
2017 Edition Square Taper Washers for High Prestressed Channels 斜墊圈（槽鐵高強度結構用） |
|
|
|
CNS 4103
2017 Edition Chain Pipe Wrenches 鏈條管鉗 |
Translated |
|
|
CNS 8331
2017 Edition Porcelain Tea Plates, Cylindrical ( replaced by CNS 981 ) 義齒床用瓷牙 |
|
|
|
CNS 13059-9
2017 Edition Photovoltaic devices Part 9: Solar simulator performance requirements 光電伏打元件（第九部：太陽模擬器之性能要求） |
|
|
|
CNS 6762
2017 Edition Morse Taper Shank Core Drills of High Speed Steel 高速鋼製取心鑽（莫氏圓錐柄） |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [336] [337] [338] [339] [340] [341] [342] |
