"C " CNS Standards List |
|
CNS 16016-5
2017 Edition PlastiCs piping systems for hot and cold water installations − Polypropylene (PP) − Part 3: Fittings 冷熱水裝置用塑膠管配管系統－聚丙烯(PP)－第5部：系統適合度 |
|
|
|
CNS 13805
2017 Edition Method of Measurement for PhotoluminesCence of Optoelectronic Semiconductor Wafers 光電半導體晶圓之光激光譜量測法 |
|
|
|
CNS 12291
2017 Edition General Rules for Reliability Assured Fixed Carbon Composition Resistors 可靠度保證混合碳固定電阻器總則 |
|
|
|
CNS 13067
2017 Edition Methods of Test for Epoxy Equivalent of Epoxy Resins 環氧樹脂之環氧當量試驗法 |
|
|
|
CNS 15968
2017 Edition PlastiCs − Film and sheeting − Measurement of water-contact angle of corona-treated films 塑膠－薄膜及薄片－電暈處理薄膜水接觸角量測法 |
|
|
|
CNS 13546-2
2017 Edition PlastiCs − Poly (methyl methacrylate) (PMMA) moulding and extrusion materials − Part 1: Designation system and basis for specifications 塑膠－聚甲基丙烯酸甲酯(PMMA)模製及押出材料－第2部：試片製備及性質測定法 |
|
|
|
CNS 12867
2017 Edition BasiC Environmental Testing Procedures Part 2 : Tests-Test Z/AM : Combined Dry Heat/Low Air Pressure Tests 環境試驗法（電氣、電子）–高溫／低氣壓複合試驗法 |
|
|
|
CNS 10695
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 13330
2017 Edition Dynamo Lamp for BiCycles 自行車（腳踏車）用發電燈 |
|
|
|
CNS 12240
2017 Edition Construction of Layered Pressure Vessels 多層卷壓力容器 |
|
|
|
CNS 11828
2017 Edition Method of Test for Blast FurnaCe Slag for Road Construction 道路用高爐爐碴檢驗法 |
Translated |
|
|
CNS 13001
2017 Edition Method of RadiographiC Testing for Circumferential Butt Welds of Aluminum Pipes and Tubes 鋁管圓周對頭熔接縫之放射線透射試驗法 |
|
|
|
CNS 4487
2017 Edition Method of test for surfaCe discontinuities –Bolts, screws and studs for general requirements 螺釘表面瑕疵檢驗法 |
|
|
|
CNS 6643
2017 Edition Safe working loads,rated-speed and slewing radius of Cranes 起重機之額定載重、額定速度與轉動半徑 |
|
|
|
CNS 3618
2017 Edition Single-Phase InduCtion Motors(under 100 Watt) １００瓦以下單相感應電動機 |
Translated |
|
|
CNS 3096
2017 Edition Hand Hammers for Forging 鍛工手鎚 |
|
|
|
CNS 3602
2017 Edition SCrew Slotting Cutters 螺釘頭槽銑刀 |
Translated |
|
|
CNS 13075
2017 Edition Non-invasive automated sphygmomanometers 非侵入式自動血壓計 |
|
|
|
CNS 14820
2017 Edition Method of test for measuring toxiC gases generated by solid material flammability － Gas detector tube 固體材料燃燒毒性氣體濃度試驗法－檢測管法 |
|
|
|
CNS 2692
2017 Edition Pliers and nippers - Pliers for gripping and manipulating 夾鉗與剪鉗－滑節轉樞夾鉗（鯉魚鉗） |
|
|
|
CNS 4367
2017 Edition KnuCkle Threads for Steel Sheet pieces (up to 0.5 mm Thickness and Appropriated Couplings Dimensions Tolerances) 圓螺紋（厚0.5mm以下之鋼皮製品及其 配合螺紋） |
|
|
|
CNS 9240
2017 Edition Method of Test for Low FreguenCy(Below 3 MHz) Electrical Connectors(TP - 18 Visual and Dimensional Inspection) 頻率３ＭＨｚ以下電連接器檢驗法（外觀及尺度檢查ＴＰ–１８） |
|
|
|
CNS 14471
2017 Edition Method of test for sulfur in petroleum produCts − High temperature combustion and IR detection 石油產品硫含量試驗法－高溫燃燒與紅外線檢測 |
|
|
|
CNS 4693
2017 Edition Fish Bolts with Round Head and Oval NeCk 魚尾板螺栓（具圓頭橢圓頸） |
|
|
|
CNS 218
2017 Edition Counter-boring Drill with Morse Taper Shank （莫氏）推拔柄柱坑鑽頭 |
Translated |
|
|
CNS 4307
2017 Edition Cross Recesses Raised Countersunk (Oval) Head Tapping Screws 十字穴扁圓頂埋頭自攻螺釘 |
|
|
|
CNS 15481-3
2017 Edition Road vehiCles - Environmental conditions and testing for electrical and electronic equipment - Part 3: Mechanical loads 道路車輛－電機電子配備環境條件與試驗－第３部：機械負載 |
|
|
|
CNS 1130
2017 Edition Pliers and nippers - Engineer's and lineman's pliers 夾鉗與剪鉗－一般技術要求 |
|
|
|
CNS 12338
2017 Edition Crowbars 撬桿 |
|
|
|
CNS 12846
2017 Edition Helium Mass SpeCtrometer Leak Testing by Trace Probe Method 氦質譜儀示蹤氣探針探漏法 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [334] [335] [336] [337] [338] [339] [340] |
