"In " CNS Standards List |
|
CNS 2863
1985 Edition Method of Test for Tolerances of RollIng Bearings 滾動軸承精度檢驗法 |
![]() |
|
|
CNS 4328
1985 Edition Electrolytic Capacitors for Motor StartIng 電動機起動用電解電容器 |
![]() |
|
|
CNS 11225
1985 Edition Liquid Penetrant Test for CastIngs 鑄件表面液滲檢驗法 |
![]() |
|
|
CNS 11290
1985 Edition Method of Test for Starch In Paper 紙中澱粉含量試驗法 |
![]() Translated |
|
|
CNS 5967
1985 Edition Bronze Screwed SwIng Check Valves (10kgf/c㎡) 青銅螺紋口擺動型止回閥(10 kgf/cm2) |
![]() |
|
|
CNS 2864
1985 Edition Deep Groove Thrust Ball BearIngs Single-Thrust, with Flat Seating 深溝止推滾珠軸承(單向具平面座外環) |
![]() |
|
|
CNS 3994
1985 Edition High Voltage CombInation Starters 高壓綜合型起動盤 |
![]() |
|
|
CNS 11376
1985 Edition Liquid Penetrant Test for ForgIngs 鍛件液滲檢驗法 |
![]() |
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽(長型封閉式,嵌於塑膠製品與壓鑄件內用) |
![]() |
|
|
CNS 4663
1984 Edition Closed Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽(片封式,嵌於塑膠製品內) |
![]() |
|
|
CNS 4661
1984 Edition Tommy Nuts with Movable ClampIng Bolt 貫頭螺帽(滑動扳桿型) |
![]() |
|
|
CNS 5280
1984 Edition Helix Angles for CylIndrical Gears 圓柱齒輪之螺旋角 |
![]() |
|
|
CNS 6777
1984 Edition Indoor Post Insulators 屋內柱形絕緣體 |
![]() |
|
|
CNS 4660
1984 Edition Tommy Nuts with Fixed ClampIng Bolt 貫頭螺帽(固定扳桿型) |
![]() |
|
|
CNS 2305
1984 Edition Asphalt LamInating Paper 夾層柏油紙 |
![]() Translated |
|
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics Mouldings 嵌入螺帽(嵌於塑膠製品內) |
![]() |
|
|
CNS 2900
1984 Edition PolyvInyl Chloride Insulated Copper Wire 聚氯乙烯絕緣屋內電話線 |
![]() Translated |
|
|
CNS 4658
1984 Edition Tommy Screws with Fixed ClampIng Bolt 貫頭螺釘(固定扳桿型) |
![]() |
|
|
CNS 4659
1984 Edition Tommy Screws with Movable ClampIng Bolt 貫頭螺釘(滑動扳桿型) |
![]() |
|
|
CNS 4664
1984 Edition Closed Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽(封閉式,嵌於塑膠製品內) |
![]() Translated |
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for FIne Mechanics 精細機械用正齒輪(因數COSα/ COSαω數值表) |
![]() |
|
|
CNS 5027
1984 Edition Control Timers for Resistance WeldIng Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
![]() |
|
|
CNS 11014
1984 Edition Methods of DetermInation for Manganese in Iron and Steel 鋼鐵中錳定量法 |
![]() |
|
|
CNS 5285
1984 Edition Accuracy of CylIndrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度(個別參數誤差之公差) |
![]() |
|
|
CNS 5284
1984 Edition Addendum Modification of Spur Gears In the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
![]() |
|
|
CNS 10795
1984 Edition Insulation Resistance Testers (Magneto Generator Operated) 絕緣電阻計(發電機式) |
![]() |
|
|
CNS 5283
1984 Edition Accuracy of CylIndrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
![]() |
|
|
CNS 6407
1984 Edition Calculation of Load Capacity for CylIndrical and Bevel Gears-Load Sharing Factor Yε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算-負載分配因數Yε及齒進度比εβ |
![]() |
|
|
CNS 5279
1984 Edition Dimensions of CylIndrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
![]() |
|
|
CNS 6408
1984 Edition Calculation of Load Capacity for CylIndrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算-齒廓面作用帶因數Z H |
![]() |
Find out:10338Items | To Page of: First -Previous-Next -Last | [325] [326] [327] [328] [329] [330] [331] |