"In " CNS Standards List |
|
CNS 3410
1985 Edition Sickles for Grass CuttIng 割草鐮刀 |
Translated |
|
|
CNS 5967
1985 Edition Bronze Screwed SwIng Check Valves (10kgf/c㎡) 青銅螺紋口擺動型止回閥(10 kgf/cm2) |
|
|
|
CNS 11377
1985 Edition Magnetic Particle Test for CastIngs and Forgings 鑄件及鍛件磁粒檢驗法 |
Translated |
|
|
CNS 11390
1985 Edition General Rules of DetermInation for Sulfur in Metallic Materials 金屬材料中硫定量法通則 |
|
|
|
CNS 4300
1985 Edition Test Code for Accuracy of Surface GrInding Machines With Horizontal Grinding Wheel Spindle and Reciprocating Table 往復床台型臥式平面磨床精度檢驗標準 |
Translated |
|
|
CNS 4301
1985 Edition Test Code for Accuracy of Surface GrInding Machines with Vertical Grinding Wheel Spindle and Rotary Table 旋轉床台型立式平面磨床精度檢驗標準 |
|
|
|
CNS 2864
1985 Edition Deep Groove Thrust Ball BearIngs Single-Thrust, with Flat Seating 深溝止推滾珠軸承（單向具平面座外環） |
|
|
|
CNS 4963
1985 Edition Test Code for Accuracy of Bench DrillIng Machines 枱式鑽床精度檢驗標準 |
Translated |
|
|
CNS 5285
1984 Edition Accuracy of CylIndrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for FIne Mechanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 5268
1984 Edition Accuracy of CylIndrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 11070
1984 Edition General Rules of DetermInation for Carbon in Metallic Materials 金屬材料中碳定量法通則 |
|
|
|
CNS 11091
1984 Edition MeasurIng Projectors 投影檢測機 |
|
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for FIne Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 5275
1984 Edition Base Tangent Lengths of Helical Gears for FIne Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 5277
1984 Edition CylIndrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 11112
1984 Edition Methods of Chemical Analysis for Lead Ingot 鉛錠分析法 |
|
|
|
CNS 11153
1984 Edition Method of Test for Effect of Organic Impurities In Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 5279
1984 Edition Dimensions of CylIndrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 5280
1984 Edition Helix Angles for CylIndrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 5282
1984 Edition Basic Rack of Gear-CuttIng Tools for Involute Tooth System 漸開線齒制用切齒刀具之基準齒條 |
|
|
|
CNS 5284
1984 Edition Addendum Modification of Spur Gears In the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 11014
1984 Edition Methods of DetermInation for Manganese in Iron and Steel 鋼鐵中錳定量法 |
|
|
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics Mouldings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 5283
1984 Edition Accuracy of CylIndrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance WeldIng Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 4664
1984 Edition Closed Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽（封閉式，嵌於塑膠製品內） |
Translated |
|
|
CNS 2305
1984 Edition Asphalt LamInating Paper 夾層柏油紙 |
Translated |
|
|
CNS 6407
1984 Edition Calculation of Load Capacity for CylIndrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算－負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 6408
1984 Edition Calculation of Load Capacity for CylIndrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算－齒廓面作用帶因數Ｚ H |
|
| Find out:10338Items | To Page of: First -Previous-Next -Last | [325] [326] [327] [328] [329] [330] [331] |
