"L " CNS Standards List |
|
CNS 14492-6
2017 Edition Methods of measurement on radio receivers for various cLasses of emission -Part 6：General purpose communication receivers 不同發射類別之無線電接收機的量測方法─第６部：一般用途通訊接收機 |
|
|
|
CNS 12243
2017 Edition PiLot Ladder 衝壓加工先導桿 |
|
|
|
CNS 4356
2017 Edition SLotted Pan Head Screws with Large Head 有槽大盤頭螺釘 |
Translated |
|
|
CNS 11572
2017 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-46 Continuity Test) 頻率３ＭＨｚ以下電連接器檢驗法（連續性試驗ＴＰ–４６） |
|
|
|
CNS 4489
2017 Edition Wing Screws, SmaLl Type 翼形頭螺釘（輕型） |
|
|
|
CNS 12254
2017 Edition Quartz CrystaL Units for Oscillators (for 200-1000 kHz) 振盪器用石英振盪晶體（２００ＫＨｚ～１０００ＫＨｚ用） |
|
|
|
CNS 6447
2017 Edition Arc WeLded Carbon Steel Pipes 配管用電弧銲碳鋼鋼管 |
Translated |
|
|
CNS 3563
2017 Edition Method of Test for Low Elongation Stress of Vulcanized Rubber 硫化橡膠低伸長應力試驗法 |
|
|
|
CNS 10673
2017 Edition CubicLe Emergency Power Source for Fire Fighting Use 消防用櫃式緊急電源受電設備 |
Translated |
|
|
CNS 10640
2017 Edition Gypsum PLaster 燒石膏 |
|
|
|
CNS 5653
2017 Edition Method of Test for Level Gauge 水平儀檢驗法 |
|
|
|
CNS 12288
2017 Edition GeneraL Rules for Reliability Assured Fixed Metal Film Resistors 可靠度保證金屬皮膜固定電阻器總則 |
|
|
|
CNS 12547
2017 Edition Method of Tension Test for Front FiLlet Welded Joint 前面填角熔接接合之拉伸試驗法 |
|
|
|
CNS 12072
2017 Edition Locating Pin of Die Casting Molds 壓鑄模用定位銷 |
|
|
|
CNS 3137
2017 Edition Large Square Head Bolts (Regular) 大方頭螺栓（一般用） |
|
|
|
CNS 4698
2017 Edition Countersunk DoubLe-rib Bolts and Counter Sinkings for Agricultural Equipment 平頂埋頭雙肋螺栓與錐坑（農業機械用） |
|
|
|
CNS 3509
2017 Edition Covered ELectrodes for Hardfacing 硬面銲被覆銲條 |
Translated |
|
|
CNS 2864
2017 Edition Deep Groove Thrust BaLl Bearings Single-Thrust, with Flat Seating 深溝止推滾珠軸承（單向具平面座外環） |
|
|
|
CNS 6399
2017 Edition DentaL Wrought Gold - Silver - Palladium Alloy 牙科用鍛造金銀鈀合金 |
|
|
|
CNS 8791
2017 Edition Method of Test for Low-Temperature Characteristics of Heat Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管低溫特性試驗法 |
|
|
|
CNS 12429
2017 Edition DeLay Electric Detonator for Engineering Use 工程用遲發電雷管 |
|
|
|
CNS 15876-2
2017 Edition Specification and quaLification of welding procedures for metallic materials − Welding procedure tests − Part 2: Arc welding of aluminium and its alloys 金屬材料銲接程序規範書及其檢定－銲接程序試驗－第2部：鋁及鋁合金的電弧銲接 |
|
|
|
CNS 12251
2017 Edition ReeLs for Magnetic Sound Recording Tapes 磁性錄音帶用捲盤 |
|
|
|
CNS 11381-1
2017 Edition GLossary of Terms for Reliability (Terms of Failure) 可靠度詞彙（有關故障之詞彙） |
|
|
|
CNS 11050
2017 Edition GeneraL Rules for Eddy Current Testing 渦電流檢測法通則 |
|
|
|
CNS 13595
2017 Edition Methods of Test for SeveraL Characteristics of Textile Floor Coverings 纖維製地毯類織物之性能試驗法 |
|
|
|
CNS 4589
2017 Edition GeneraL Rules of Fixed Capacitors for Use in Electronic Equipment 電子設備用固定電容器通則 |
|
|
|
CNS 10698
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Squelch Blocking, Receiver Attack and Closing Time) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（靜音截斷、接收機動作及閉合時間） |
|
|
|
CNS 10150
2017 Edition Test Code for Accuracy of VerticaL Multi-Spindle Drilling Machines 立式多軸鑽床之精度檢驗標準 |
|
|
|
CNS 5993
2017 Edition CoiL Springs for Press Dies 衝模用螺旋彈簧 |
|
| Find out:14127Items | To Page of: First -Previous-Next -Last | [320] [321] [322] [323] [324] [325] [326] |
