"L, " CNS Standards List |
|
CNS 4659
2017 Edition Tommy Screws with Movable Clamping Bolt 貫頭螺釘（滑動扳桿型） |
|
|
|
CNS 15481-5
2017 Edition Road vehicles - EnvironmentaL conditions and testing for electrical and electronic equipment - Part 5: Chemical loads 道路車輛－電機電子配備環境條件與試驗－第５部： 化學負載 |
|
|
|
CNS 3975
2017 Edition Flat Chisels 扁鑿 |
Translated |
|
|
CNS 13982-3
2017 Edition Methods of test for bulk down and feather − Part 3: Composition (content analysis) 羽絨羽毛試驗法－第3部：組成 |
|
|
|
CNS 15986-5
2017 Edition Quality requirements for fusion welding of metallic materials − Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements of CNS 15986-2, CNS 15986-3 or CNS 15986-4 金屬材料熔融銲接的品質要求－第5部：宣告符合CNS 15986-2、CNS 15986-3或CNS 15986-4時應符合之文件 |
|
|
|
CNS 13811
2017 Edition Numerical-Type Reflectors for Light Emitting Diodes 發光二極體數字型反射套板 |
|
|
|
CNS 4172
2017 Edition Short Pitch Transmission Precision Bush Chains and Chain Wheels 短節距傳動用精確襯套鏈條及鏈輪 |
|
|
|
CNS 4608
2017 Edition Studs for Welding 螺樁（熔接用） |
|
|
|
CNS 12807
2017 Edition Quality Requirement for Microfilm of Documents and Drawings 微縮品製作–文件及圖面微縮軟片品質之要求 |
|
|
|
CNS 4152
2017 Edition Valve for Dissolved Acetylene Cylinder 溶解乙炔氣鋼瓶閥 |
Translated |
|
|
CNS 3610
2017 Edition Two-Flute End Mills with Straight Shank 兩刃直柄端銑刀 |
Translated |
|
|
CNS 11933
2017 Edition Ejector Guide Pins of Molds for Plastics 塑膠型模用頂出導銷 |
|
|
|
CNS 10237
2017 Edition Handles for Cranes 起重機用手柄 |
|
|
|
CNS 1188
2017 Edition Flat File for Carpenter, Sharp Flat End 木工用尖平頭扁平銼 |
Translated |
|
|
CNS 3429
2017 Edition Silicone Varnished Glass Cloth 漆矽玻璃纖維布 |
|
|
|
CNS 9796
2017 Edition Saddle supported horizontaL pressure vessels 以鞍座支撐之臥型壓力容器 |
|
|
|
CNS 13722
2017 Edition Documentation-Headers for Microfiche of Monographs and Serials 文獻–圖書與期刊的微縮單片標題 |
|
|
|
CNS 2774
2017 Edition Unbleached softwood sulfate pulp (USKP) 未漂白針葉樹硫酸鹽木漿 |
|
|
|
CNS 13040
2017 Edition Covered electrodes for 9% nickeL steel ９﹪鎳鋼用被覆銲條 |
|
|
|
CNS 8973
2017 Edition Quenched and Tempered Manganese-Molybdenum and Manganese-Molybdenum-NickeL Alloy Steel Plates for Pressure Vessels 壓力容器用淬火–回火之錳鉬及錳鉬鎳合金鋼鋼板 |
|
|
|
CNS 3974
2017 Edition Cold Chisels 鍛工用冷鑿 |
Translated |
|
|
CNS 5993
2017 Edition CoiL Springs for Press Dies 衝模用螺旋彈簧 |
|
|
|
CNS 7865
2017 Edition Laminated Springs Spring Link Washers and Intermediate Spring Link Washers for Spring Suspension 彈簧板端鞍板及中間板懸吊彈簧用 |
Translated |
|
|
CNS 12254
2017 Edition Quartz CrystaL Units for Oscillators (for 200-1000 kHz) 振盪器用石英振盪晶體（２００ＫＨｚ～１０００ＫＨｚ用） |
|
|
|
CNS 366-9
2017 Edition Safety requirements for cycles − Part 9: Saddles and seat-post test methods 自行車安全要求－第9部：座墊及座桿測試法 |
|
|
|
CNS 3574
2017 Edition Method of test for flash point by Pensky-Martens closed cup tester 閃點試驗法(潘-馬氏閉杯式法) |
|
|
|
CNS 4418
2017 Edition Countersunk Square Bolts with Long Square 平頂埋頭長方頸螺栓 |
|
|
|
CNS 10726
2017 Edition Method of Test for Printing Ink Permeation of Paper (Castor OiL Test) 紙張之印刷油墨滲透性試驗法（蓖麻油法） |
Translated |
|
|
CNS 10698
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Squelch Blocking, Receiver Attack and Closing Time) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（靜音截斷、接收機動作及閉合時間） |
|
|
|
CNS 14367
2017 Edition Photography-Film dimensions-Micrographics 照相技術－軟片尺度－用於微縮技術之軟片 |
|
| Find out:14127Items | To Page of: First -Previous-Next -Last | [318] [319] [320] [321] [322] [323] [324] |
