"N " CNS Standards List |
|
CNS 13982-2
2017 Edition Methods of test for bulk dowN and feather − Part 2: Sampling 羽絨羽毛試驗法－第2部：抽樣 |
|
|
|
CNS 1132
2017 Edition Pliers aNd nippers - Diagonal cutting nippers 夾鉗與剪鉗－對口剪鉗（平口鉗） |
|
|
|
CNS 12887-1
2017 Edition Method of Test for Accelerated AgiNg of Paper and Paperboard - Moist Heat Treatment at 80℃ and 65% R.H. 紙及紙板加速老化試驗法─80℃及65％R.H.濕熱處理 |
Translated |
|
|
CNS 9705
2017 Edition GeNeral Rules for Emission-Spectroscopic Analysis of Iron and Steel 鐵及鋼之發光光譜分析法通則 |
|
|
|
CNS 12865-2
2017 Edition Method of Test for Digital MicroelectroNics ( Low Level Output Voltage ) 數位微電子檢驗法（低位準輸出電壓） |
|
|
|
CNS 14866-2
2017 Edition MeasuremeNt of water flow in fully charged closed conduits - Meters for cold potable water and hot water - Part 2: Installation requirements 完全充滿的密閉導管內水流量之量測－冷飲水及熱水用水量計－第2部：安裝要求 |
|
|
|
CNS 15562-7
2017 Edition StatioNary training equipment − Part 7: Rowing machines − Additional specific safety requirements and test methods 固定式訓練設備－第7部：划船機－附加之特定安全要求與試驗法 |
|
|
|
CNS 6834-8
2017 Edition TestiNg methods for rubber and plastics hoses - Part 8: Hydraulic – pressure impulse test without flexing 橡膠管及塑膠管試驗法－第8部：無撓曲液壓脈衝試驗 |
|
|
|
CNS 3497
2017 Edition CaNned tomatoes 番茄罐頭 |
|
|
|
CNS 7003
2017 Edition MachiNe Taper Pin Reamers with Morse Taper Shanks 推拔銷鉸刀（莫氏圓錐柄，機用） |
|
|
|
CNS 8473
2017 Edition PiN Allocations for Microprocessor Systems Using the Connector for Frequencies Below 3 MHz for Use with Printed Boards 衝頭（打銷用） |
|
|
|
CNS 9803
2017 Edition WeldiNg procedure qualification test for pressure vessels 壓力容器熔接施工方法之確認試驗 |
|
|
|
CNS 14555
2017 Edition Road traffic LED display paNel 道路用發光二極體文字顯示型交通資訊看板 |
|
|
|
CNS 12937
2017 Edition Structure of Welded SteelTaNks for Petroleum Oil Storage 鋼製全熔接石油類儲槽構造 |
|
|
|
CNS 13804
2017 Edition GuidaNce on the Use of the Substitution Method for Measurements of Radiation from Microwave Ovens for Frequencies above 1 GHz 應用置換法測量微波爐１ＧＨｚ以上之輻射指引 |
Translated |
|
|
CNS 15347
2017 Edition Safety of machiNery − General principles for design − Risk assessment and risk reduction 機械安全－設計之一般原則－風險評鑑及風險降低 |
|
|
|
CNS 2958
2017 Edition Cast-iroN Pipes and Fittings for Sanitary Equipments 衛生設備用鑄鐵管及管件 |
|
|
|
CNS 15581
2017 Edition GradiNg rules for hardwood sawn lumber 闊葉樹製材分等 |
|
|
|
CNS 11400
2017 Edition Method of Eddy CurreNt Test for Metal Bars Rods and Wires 金屬棒桿及線渦電流檢驗法 |
|
|
|
CNS 15115
2017 Edition ThiN-film terrestrial photovoltaic (PV) modules - Design qualification and type approval 薄膜陸上型太陽光電模組－設計確認和型式認可 |
|
|
|
CNS 15767-2-7
2017 Edition Plugs aNd socket-outlets for household and similar purposes − Part 2-7: Particular requirements for cord extension sets 家用和類似用途插頭及插座－第2-7部：延長用電源線組之特定要求 |
|
|
|
CNS 6544
2017 Edition Cast steel travelliNg wheel for overhead travelling cranes 架空移動起重機用鑄鋼製直行車輪 |
|
|
|
CNS 14466-8
2017 Edition Audiovisual,video aNd television equipment and systems. Part8:Syinbols and identification 視聽．影像及電視設備與系統-第８部：符號標誌與識別 |
|
|
|
CNS 12729
2017 Edition Packaged soybeaN curd (Tofu) 包裝豆腐 |
|
|
|
CNS 4491
2017 Edition LiftiNg Eye Bolts 吊環螺釘 |
|
|
|
CNS 15207-10
2017 Edition Road vehicles - CompoNent test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 10: Immunity to conducted disturbances in the extended audio frequency range 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第10部：音頻延伸範圍之傳導擾動免疫力 |
|
|
|
CNS 11156
2017 Edition Grease GuNs-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 15969
2017 Edition Structural requiremeNts of railway vehicle bodies of the locomotives and passenger rolling stock 機車及客車軌道車輛車體結構要求 |
|
|
|
CNS 283
2017 Edition Methods of sampliNg and chemical analysis of common salt 工業鹽取樣法及化學分析法 |
|
|
|
CNS 14466-18
2017 Edition Audiovisual, video aNd television equipment and systems - Part18: Connectors for automatic slide projectors withe built-in triacs for audiovisual application 視聽．影像及電視設備與系統-第１８部：視聽應用具內建三端閘流體之自動幻燈片投影機之連接器 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [316] [317] [318] [319] [320] [321] [322] |
