"N " CNS Standards List |
|
CNS 1358
2017 Edition Method of Test for FoldiNg Endurance of Paper by Schopper type Tester 紙之蕭波式耐折強度試驗法 |
Translated |
|
|
CNS 1014
2017 Edition Picks (SiNgle), One Taper End Only 十字鎬（各部份名稱） |
|
|
|
CNS 11156
2017 Edition Grease GuNs-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 11329
2017 Edition Test Method for the Sets of High StreNgth Hexagon Bolt, Hexagon Nut and Plain Washers for Friction Grip Joints 摩擦接合用高強度六角螺栓、六角螺帽及平墊圈組合件檢驗法 |
|
|
|
CNS 5770
2017 Edition GeNeral Specification for Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 283
2017 Edition Methods of sampliNg and chemical analysis of common salt 工業鹽取樣法及化學分析法 |
|
|
|
CNS 13464
2017 Edition Method of Liquid PeNetrant Test for the Welds of Steel Structure 鋼結構銲道液滲檢測法 |
|
|
|
CNS 6860
2017 Edition Respiratory protective devices − Self-coNtained open-circuit compressed air breathing apparatus with full face mask − Requirements, testing, marking 呼吸防護裝置－全面罩壓縮空氣開放式自攜呼吸器－要求、試驗、標示 |
|
|
|
CNS 503
2017 Edition ISO Metric FiNe Screw Threads (Diameters from 18 to 150mm and Pitch 2mm) 公制細螺紋6（ISO制）（標稱直徑18至150公釐，螺距2公釐） |
|
|
|
CNS 12865-1
2017 Edition Method of Test for Digital MicroelectroNics ( High Level Output Voltage ) 數位微電子檢驗法（高位準輸出電壓） |
|
|
|
CNS 12887-1
2017 Edition Method of Test for Accelerated AgiNg of Paper and Paperboard - Moist Heat Treatment at 80℃ and 65% R.H. 紙及紙板加速老化試驗法─80℃及65％R.H.濕熱處理 |
Translated |
|
|
CNS 15581
2017 Edition GradiNg rules for hardwood sawn lumber 闊葉樹製材分等 |
|
|
|
CNS 8918
2017 Edition Primary StaNdards ( replaced by CNS 12983 ) 固定式消防用加壓離心泵之原動機 |
|
|
|
CNS 14466-18
2017 Edition Audiovisual, video aNd television equipment and systems - Part18: Connectors for automatic slide projectors withe built-in triacs for audiovisual application 視聽．影像及電視設備與系統-第１８部：視聽應用具內建三端閘流體之自動幻燈片投影機之連接器 |
|
|
|
CNS 9369
2017 Edition Method of Test for Low FrequeNcy (Below 3 MHz) Electrical Connectors (TP - 35 Proposed Insert Retention) 頻率３ＭＨｚ以下電連接器檢驗法（接觸端子插入扣鎖ＴＰ–３５） |
|
|
|
CNS 12784
2017 Edition Method of Test for IN-Plane Shear Propetries of Glass Fiber Reinforced Plastics 玻璃纖維強化塑膠之面內剪斷性能測定法 |
|
|
|
CNS 4579
2017 Edition Bolted CoNnections with Reduced Body; Bolts 減徑柄螺栓之結合法（螺栓） |
|
|
|
CNS 11400
2017 Edition Method of Eddy CurreNt Test for Metal Bars Rods and Wires 金屬棒桿及線渦電流檢驗法 |
|
|
|
CNS 12937
2017 Edition Structure of Welded SteelTaNks for Petroleum Oil Storage 鋼製全熔接石油類儲槽構造 |
|
|
|
CNS 698
2017 Edition Method of Test for Activated CarboN (Power, for Industrial Use) 工業用活性碳（粉狀）檢驗法 |
|
|
|
CNS 6834-8
2017 Edition TestiNg methods for rubber and plastics hoses - Part 8: Hydraulic – pressure impulse test without flexing 橡膠管及塑膠管試驗法－第8部：無撓曲液壓脈衝試驗 |
|
|
|
CNS 14257
2017 Edition Method of test for leakage rate respirator facepiece 呼吸防護具面體洩漏率試驗法 |
|
|
|
CNS 1217
2017 Edition Method of practice for maNual sampling of petroleum and petroleum products 石油及其產品手動取樣法 |
|
|
|
CNS 2671
2017 Edition GalvaNized Low Carbon Steel Wire Strand 鍍鋅低碳鋼絞線 |
|
|
|
CNS 4252
2017 Edition SpriNg Washers Curved or Crinkle Type 反向曲線形或波浪形彈簧墊圈（高壓縮負荷彈簧墊圈） |
|
|
|
CNS 13194
2017 Edition Test Methods for PerformaNce and Accuracy of Double Sizers 雙端截鋸機之性能試驗及精度檢驗法 |
|
|
|
CNS 12865-2
2017 Edition Method of Test for Digital MicroelectroNics ( Low Level Output Voltage ) 數位微電子檢驗法（低位準輸出電壓） |
|
|
|
CNS 66
2017 Edition Square Heads aNd Holes (for Shaft, Hand Wheel and Handles) 方頭及方孔（用於軸，手輪及手柄） |
|
|
|
CNS 5970
2017 Edition BroNze Flanged Angle Valves (10kgf/c㎡) 青銅凸緣型角閥（10 kgf/㎠） |
|
|
|
CNS 8473
2017 Edition PiN Allocations for Microprocessor Systems Using the Connector for Frequencies Below 3 MHz for Use with Printed Boards 衝頭（打銷用） |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [316] [317] [318] [319] [320] [321] [322] |
