"G " CNS Standards List |
|
CNS 11158
1984 Edition TunGsten-Carbide Bits and Rod for Rock Drill Sets 鑽石用碳化鎢鑽刃及鑽桿組 |
|
|
|
CNS 11157
1984 Edition Lubrication Holes, Grooves and Bore Reliefs 潤滑孔、潤滑槽、潤滑坑 |
|
|
|
CNS 5285
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 10993
1984 Edition Methods of TestinG Preformed Expansion Joint Fillers for Concrete (Nonextruding and Resilient Types) 混凝土伸縮縫預製填縫物試驗法（凹式） |
|
|
|
CNS 5284
1984 Edition Addendum Modification of Spur Gears in the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 11014
1984 Edition Methods of Determination for ManGanese in Iron and Steel 鋼鐵中錳定量法 |
|
|
|
CNS 11154
1984 Edition Grease Guns-Rush Type Hand Guns 手用衝壓式黃油槍 |
|
|
|
CNS 11153
1984 Edition Method of Test for Effect of OrGanic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 11151
1984 Edition Method of Test for Unit WeiGht, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 11112
1984 Edition Methods of Chemical Analysis for Lead InGot 鉛錠分析法 |
|
|
|
CNS 11091
1984 Edition MeasurinG Projectors 投影檢測機 |
|
|
|
CNS 11070
1984 Edition General Rules of Determination for Carbon in Metallic Materials 金屬材料中碳定量法通則 |
|
|
|
CNS 5283
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 6410
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 4664
1984 Edition Closed Insert Nuts with Dead Hole for Plastics MouldinGs 嵌入螺帽（封閉式，嵌於塑膠製品內） |
Translated |
|
|
CNS 4732
1984 Edition Knurled Nuts with RinG 有環滾紋螺帽 |
|
|
|
CNS 4659
1984 Edition Tommy Screws with Movable ClampinG Bolt 貫頭螺釘（滑動扳桿型） |
|
|
|
CNS 4731
1984 Edition Knurled Nuts for DrawinG Instruments 滾紋螺帽（製圖儀器用） |
|
|
|
CNS 4730
1984 Edition LiftinG Eye Nuts 圓形環首螺帽 |
|
|
|
CNS 9705
1984 Edition General Rules for Emission-Spectroscopic Analysis of Iron and Steel 鐵及鋼之發光光譜分析法通則 |
|
|
|
CNS 4663
1984 Edition Closed Insert Nuts with Disk for Plastics MouldinGs 嵌入螺帽（片封式，嵌於塑膠製品內） |
|
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics MouldinGs and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 4733
1984 Edition HexaGon Nuts with Collar 突緣六角螺帽 |
|
|
|
CNS 5267
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Cumulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 6408
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算－齒廓面作用帶因數Ｚ H |
|
|
|
CNS 4658
1984 Edition Tommy Screws with Fixed ClampinG Bolt 貫頭螺釘（固定扳桿型） |
|
|
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics MouldinGs 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 4661
1984 Edition Tommy Nuts with Movable ClampinG Bolt 貫頭螺帽（滑動扳桿型） |
|
|
|
CNS 4660
1984 Edition Tommy Nuts with Fixed ClampinG Bolt 貫頭螺帽（固定扳桿型） |
|
| Find out:10068Items | To Page of: First -Previous-Next -Last | [316] [317] [318] [319] [320] [321] [322] |
