"L " CNS Standards List |
|
CNS 3610
2017 Edition Two-FLute End Mills with Straight Shank 兩刃直柄端銑刀 |
![]() Translated |
|
|
CNS 5056
2017 Edition Loose Tenon Blocks 活榫塊 |
![]() |
|
|
CNS 11168
2017 Edition Iron and steeL – Methods for determination of cobalt content 鐵及鋼-鈷定量法 |
![]() |
|
|
CNS 3421
2017 Edition Safety Code for Power RoLling Machines (Inspection) 動力壓機安全規章(檢查) |
![]() |
|
|
CNS 4327
2017 Edition Capacitors for ELectrical Apparatus 電器用電容器 |
![]() |
|
|
CNS 128
2017 Edition Metric Taper Gauge, Without FLat Head 公制圓錐量規(無扁頭) |
![]() |
|
|
CNS 4851
2017 Edition Screwed SeaLing Plugs for Drain Fittings of High Density PE 螺旋塞(用於排水配件者,硬質聚乙烯製) |
![]() |
|
|
CNS 4320
2017 Edition Hexagon Head BoLts, Finished and Semi-Finished, Metric Fine Thread 六角頭螺栓(精製及半精制,公制細螺紋) |
![]() |
|
|
CNS 12293
2017 Edition ReLiability Assured Fixed Carbon Composition Resistors (From 1, Grade X) 可靠度保證混合碳固定電阻器(方式1之等級X) |
![]() Translated |
|
|
CNS 4404
2017 Edition Serrated Lock Washers 鋸齒墊圈 |
![]() |
|
|
CNS 1197
2017 Edition Round FiLe for Smith 鐵工用圓銼 |
![]() Translated |
|
|
CNS 4311
2017 Edition CLevis Pins U形環插銷 |
![]() |
|
|
CNS 4844
2017 Edition Heavy Type Hexagon Head Pipe PLugs with Shoulder, Vent Hole and Parallel Thread 重型六角頭管塞(具肩部、通氣孔與平行螺紋) |
![]() |
|
|
CNS 13143
2017 Edition Method of Test for InternaL Bonding Strength Paperboard ( Using Z- direction Tensile / Compression Tester) 紙板內部結合強度試驗法(使用Z–方向拉/壓式試驗機) |
![]() Translated |
|
|
CNS 4412
2017 Edition SLotted Countersunk (Flat) Head Screws with Full Dog Point 有槽平頂埋頭長柱端螺釘 |
![]() |
|
|
CNS 13007
2017 Edition MAG WeLding Flux Cored Wire for Molybdenum Steel and Chrominum Molybdenum Steel 鉬鋼及鉻鉬鋼MAG熔接用空心填入熔劑鋼線 |
![]() |
|
|
CNS 60227-1
2017 Edition PoLyvinyl chloride insulated cables of rated voltages up to and including 450/750V − Part 1: General requirements 額定電壓450/750 V以下聚氯乙烯絕緣電纜-第1 部:一般要求 |
![]() |
|
|
CNS 4649
2017 Edition PLain Thrust Bearings Tilting Pad Thrust Bearings Boundary Dimensions 硬化光墊圈 |
![]() Translated |
|
|
CNS 7962
2017 Edition Test Code for Performance of NumericaLly Controlled Table Type Horizontal Boring Machines 數值控制床台型臥式搪床動態檢驗法 |
![]() |
|
|
CNS 2181
2017 Edition Method of Test for Power TiLler 耕耘機檢驗法 |
![]() |
|
|
CNS 10541
2017 Edition Test Code for Performance of Wood Borers and HoLlow Chisel Motisers 木工鑽及角鑿機動態檢驗法 |
![]() |
|
|
CNS 12253
2017 Edition Quartz CrystaL Units For Oscillators (For 1 MHz -- 125 MHz) 振盪器用石英振盪晶體(1MHz~125MHz用) |
![]() |
|
|
CNS 4708
2017 Edition PLastic drinking straw 直流用塑膠膜電容器(特牲M) |
![]() Translated |
|
|
CNS 7139
2017 Edition GeneraL Rules of Dust Test for Automobile Parts 汽車零件之防塵及耐塵試驗通則 |
![]() |
|
|
CNS 14673
2017 Edition Interference to mobiLe radiocommunications in the presence of impulsive noise - Methods of judging degradation and measures to improve performance 脈衝性雜訊對行動無線通信的干擾-產品劣化的判定方式及其性能的改善方法 |
![]() |
|
|
CNS 3415
2017 Edition Safety Code for Power RoLling Machines (General Rule) 動力壓機安全規章(總則) |
![]() |
|
|
CNS 4664
2017 Edition CLosed Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽(封閉式,嵌於塑膠製品內) |
![]() Translated |
|
|
CNS 11070
2017 Edition GeneraL Rules of Determination for Carbon in Metallic Materials 金屬材料中碳定量法通則 |
![]() |
|
|
CNS 12865-9
2017 Edition Method of Test for DigitaL Microelectronics ( Delay Measurements ) 數位微電子檢驗法(延遲量測) |
![]() |
|
|
CNS 4079
2017 Edition Wire Spring ReLay 線簧電驛 |
![]() |
Find out:14127Items | To Page of: First -Previous-Next -Last | [314] [315] [316] [317] [318] [319] [320] |