"f " CNS Standards List |
|
CNS 11299-5
2017 Edition Glossary of terms for sensing and transducing (Terms of measurement signal processing for general instrument technology) 感測與轉換詞彙(有關一般儀表技術之量測信號處理名詞) |
![]() |
|
|
CNS 13810
2017 Edition Lead frames for Light Emitting Diodes 發光二極體用支架 |
![]() |
|
|
CNS 15091-6
2017 Edition Method of test for deep sea water - Determination of dissolved oxygen 深層海水檢驗法-溶氧量之測定 |
![]() |
|
|
CNS 10206
2017 Edition Quick connector for fire hose 消防水帶用快速接頭 |
![]() |
|
|
CNS 11476
2017 Edition General Test Procedure of Failure Rate for Electronic Components 電子零組件故障率試驗法通則 |
![]() |
|
|
CNS 14594
2017 Edition Covered electrodes for cast iron 鑄鐵用被覆銲條 |
![]() |
|
|
CNS 6642
2017 Edition Calculated capacity for unloader 卸載機之計算卸載能力 |
![]() |
|
|
CNS 14492-9
2017 Edition Methods of measurement on radio receivers for various classes of emission -Part 9:Measurement of the characteristics relevant to radio data system (RDS) reception 不同發射類別之無線電接收機的量測方法─第9部:無線電數據系統﹝RDS﹞接收相關特性值的量測 |
![]() |
|
|
CNS 8875
2017 Edition fire Alarm Equipment Repeaters 火警中繼器 |
![]() Translated |
|
|
CNS 5266
2017 Edition Series of Modules for Worm Gear Pairs 齒輪模數(蝸桿蝸輪對) |
![]() |
|
|
CNS 11352
2017 Edition Method of Comparison for Surface Colour 表面色之比較方法 |
![]() |
|
|
CNS 13394
2017 Edition Method of Test for Viscosity of Pulp (Falling Ball Method) 紙漿黏度試驗法(落球法) |
![]() Translated |
|
|
CNS 13352-2
2017 Edition Micrographics Vocabulary (Section 02: Image Positions and Methods of Recording) 微縮技術詞彙(第二部:影像位置與縮攝方式) |
![]() |
|
|
CNS 15210-2
2017 Edition Information technology - Radio frequency identification for item management - Part 2: Parameters for air interface communications below 135kHz 資訊技術-品項管理之無線射頻識別-第2部:低於135kHz空中介面通信參數 |
![]() |
|
|
CNS 1410
2017 Edition Strengthened fiber Separator for Lead Storage Batteries 蓄電池用強化纖維隔離板 |
![]() |
|
|
CNS 12838
2017 Edition Method of Test for Polyvinyl Chloride Medical Gloves 一般醫療用聚氯乙烯手套檢驗法 |
![]() |
|
|
CNS 9365
2017 Edition Method of Test for Low Frequency(Below 3 MHz) Electrical Connectors (TP - 6 Contact Resistance) 頻率3MHz以下電連接器檢驗法(接觸電阻TP–6) |
![]() |
|
|
CNS 4073
2017 Edition Assembly tools for screws and nuts - Forged and tubular socket wrenches - Maximumhead dimensions 螺釘及螺帽之裝配工具–鍛製及管製套筒扳手之最大外徑 |
![]() |
|
|
CNS 15481-2
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 2: Electrical loads 道路車輛-電機電子配備環境條件與試驗-第2部:電力負載 |
![]() |
|
|
CNS 12122
2017 Edition Method of Test on Communication Receivers for Amplitude-Modulation Transmissions 調幅通信接收機檢驗法 |
![]() |
|
|
CNS 10734
2017 Edition Method of Test for the Plastic Rims of Bicycle 平車或跑車型自行車塑膠輪圈檢驗法 |
![]() |
|
|
CNS 13059-2
2017 Edition Photovoltaic devices Part2:Requirements for reference solar cells 光電伏打元件﹝第二部:基準太陽電池之要求﹞ |
![]() |
|
|
CNS 4945
2017 Edition Adjusting Screws for Drawing Instruments 製圖儀器用調整螺釘 |
![]() |
|
|
CNS 11040
2017 Edition Method of Conical Cup Test 錐杯試驗法 |
![]() |
|
|
CNS 5497
2017 Edition feed Forked Connections for Industrial Sewing Machines 工業用縫紉機送料叉桿 |
![]() |
|
|
CNS 6735
2017 Edition folding Shovel 折疊元鍬 |
![]() |
|
|
CNS 12592
2017 Edition Method of Test for Total Wax Content of Corrugated Paperboard 瓦楞紙板含蠟量試驗法 |
![]() Translated |
|
|
CNS 4691
2017 Edition Studs for Stud Welding With Tip Ignition; Threaded Studs 尖端燃熔用螺樁 |
![]() |
|
|
CNS 5495
2017 Edition Needle Clamp Bodies of Sewing Machines for Industrial Use 工業用縫紉機針固定環 |
![]() |
|
|
CNS 11942
2017 Edition General Rules of Chemical Analysis for Copper Products and Copper Alloys 銅及銅合金分析法通則 |
![]() |
Find out:12815Items | To Page of: First -Previous-Next -Last | [306] [307] [308] [309] [310] [311] [312] |