"R " CNS Standards List |
|
CNS 16022
2017 Edition Acoustics − DeteRmination of dynamic stiffness − Part 1: Materials used under floating floors in dwellings 聲學－動態剛性測定法－用於住宅浮式地板下之材料 |
|
|
|
CNS 1358
2017 Edition Method of Test foR Folding Endurance of Paper by Schopper type Tester 紙之蕭波式耐折強度試驗法 |
Translated |
|
|
CNS 14257
2017 Edition Method of test foR leakage rate respirator facepiece 呼吸防護具面體洩漏率試驗法 |
|
|
|
CNS 12565
2017 Edition Basic EnviRonmental Testing Procedures Part 2: Tests, Test Db: Damp Heat, Cycle (12+12-Hour Cycle) 環境試驗方法（電氣、電子）–溫濕度循環（１２＋１２小時循環）試驗方法 |
|
|
|
CNS 2958
2017 Edition Cast-iRon Pipes and Fittings for Sanitary Equipments 衛生設備用鑄鐵管及管件 |
|
|
|
CNS 12865-2
2017 Edition Method of Test foR Digital Microelectronics ( Low Level Output Voltage ) 數位微電子檢驗法（低位準輸出電壓） |
|
|
|
CNS 14109-2
2017 Edition MicRofilming of technical drawings and other drawing office documents--Part2:Quality criteria and control of 35mm silver gelatin microfilms 技術類製圖和其他規格化製圖文件之微縮--第二部:35mm銀鹽軟片的品質規範與控制 |
|
|
|
CNS 5770
2017 Edition GeneRal Specification for Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 11400
2017 Edition Method of Eddy CuRrent Test for Metal Bars Rods and Wires 金屬棒桿及線渦電流檢驗法 |
|
|
|
CNS 12729
2017 Edition Packaged soybean cuRd (Tofu) 包裝豆腐 |
|
|
|
CNS 12937
2017 Edition StRucture of Welded SteelTanks for Petroleum Oil Storage 鋼製全熔接石油類儲槽構造 |
|
|
|
CNS 8917
2017 Edition StationaRy Centrifugal Fire Pumps 固定式消防用加壓離心泵 |
|
|
|
CNS 15969
2017 Edition StRuctural requirements of railway vehicle bodies of the locomotives and passenger rolling stock 機車及客車軌道車輛車體結構要求 |
|
|
|
CNS 8473
2017 Edition Pin Allocations foR Microprocessor Systems Using the Connector for Frequencies Below 3 MHz for Use with Printed Boards 衝頭（打銷用） |
|
|
|
CNS 13194
2017 Edition Test Methods foR Performance and Accuracy of Double Sizers 雙端截鋸機之性能試驗及精度檢驗法 |
|
|
|
CNS 6834-8
2017 Edition Testing methods foR rubber and plastics hoses - Part 8: Hydraulic – pressure impulse test without flexing 橡膠管及塑膠管試驗法－第8部：無撓曲液壓脈衝試驗 |
|
|
|
CNS 14866-2
2017 Edition MeasuRement of water flow in fully charged closed conduits - Meters for cold potable water and hot water - Part 2: Installation requirements 完全充滿的密閉導管內水流量之量測－冷飲水及熱水用水量計－第2部：安裝要求 |
|
|
|
CNS 8918
2017 Edition PRimary Standards ( replaced by CNS 12983 ) 固定式消防用加壓離心泵之原動機 |
|
|
|
CNS 6544
2017 Edition Cast steel tRavelling wheel for overhead travelling cranes 架空移動起重機用鑄鋼製直行車輪 |
|
|
|
CNS 11156
2017 Edition GRease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 7003
2017 Edition Machine TapeR Pin Reamers with Morse Taper Shanks 推拔銷鉸刀（莫氏圓錐柄，機用） |
|
|
|
CNS 15207-10
2017 Edition Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 10: Immunity to conducted disturbances in the extended audio frequency range 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第10部：音頻延伸範圍之傳導擾動免疫力 |
|
|
|
CNS 15911
2017 Edition Child use and caRe articles − Children’s bedguards for domestic use 兒童照護用品－家用兒童床邊護欄 |
Translated |
|
|
CNS 15115
2017 Edition Thin-film teRrestrial photovoltaic (PV) modules - Design qualification and type approval 薄膜陸上型太陽光電模組－設計確認和型式認可 |
|
|
|
CNS 9555
2017 Edition Pallet tRucks - Principal dimensions 拖板車－主要尺度 |
|
|
|
CNS 5516
2017 Edition Induction Type OveRcurrent Relay for High Voltage Receiving 高壓受電用感應式過電流電譯 |
|
|
|
CNS 5970
2017 Edition BRonze Flanged Angle Valves (10kgf/c㎡) 青銅凸緣型角閥（10 kgf/㎠） |
|
|
|
CNS 12426
2017 Edition Pulp, papeR and paperboard - Measurement of diffuse blue reflectance factor (ISO brightness) 紙漿－供光學性質測定之試樣製備法 |
|
|
|
CNS 15466
2017 Edition Testing method of peRformance for air source heat pump water heaters 空氣源式熱泵熱水器之性能試驗法 |
|
|
|
CNS 4809
2017 Edition GeneRal Rules for Accuracy Inspection of Woodworking Machines 木工機械精度檢驗通則 |
|
| Find out:15408Items | To Page of: First -Previous-Next -Last | [302] [303] [304] [305] [306] [307] [308] |
