"A " CNS Standards List |
|
CNS 15466
2017 Edition Testing method of performAnce for air source heat pump water heaters 空氣源式熱泵熱水器之性能試驗法 |
|
|
|
CNS 15233
2017 Edition Fixtures of roAdway lighting with light emitting diode lamps 發光二極體道路照明燈具 |
Translated |
|
|
CNS 2671
2017 Edition GAlvanized Low Carbon Steel Wire Strand 鍍鋅低碳鋼絞線 |
|
|
|
CNS 12565
2017 Edition BAsic Environmental Testing Procedures Part 2: Tests, Test Db: Damp Heat, Cycle (12+12-Hour Cycle) 環境試驗方法（電氣、電子）–溫濕度循環（１２＋１２小時循環）試驗方法 |
|
|
|
CNS 8784
2017 Edition Method of Test for Tensile of HeAt Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管拉伸試驗法 |
|
|
|
CNS 4969
2017 Edition BAnd Saw Blades for Woodworking Machines 木工機械用鋸片帶 |
|
|
|
CNS 783-3-2
2017 Edition Sodium cArbonate for industrial use - Part 3-2 : Determination of total soluble alkalinity - Potentiometric method 工業用碳酸鈉－第３－２部：總可溶性鹼含量測定法－電位差滴定法 |
|
|
|
CNS 8473
2017 Edition Pin Allocations for Microprocessor Systems Using the Connector for Frequencies Below 3 MHz for Use with Printed Boards 衝頭（打銷用） |
|
|
|
CNS 13065
2017 Edition Methods of Test for Viscosity of Epoxy Resins And Hardeners 環氧樹脂及硬化劑黏度測定法 |
|
|
|
CNS 7248
2017 Edition Liquefied Petroleum GAstank on Truck or Trailer 液化石油氣汽車運輸槽體 |
|
|
|
CNS 11156
2017 Edition GreAse Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 4306
2017 Edition Cross Recesses Countersunk (FlAt) Head Tapping Screws 十字穴平頂埋頭自攻螺釘 |
|
|
|
CNS 2178
2017 Edition Liquid MembrAne-Forming Compounds for Curing Concrete 混凝土用液膜養護劑 |
Translated |
|
|
CNS 15998
2017 Edition Rubber compounding ingredients − CArbon black − Determination of aggregate size distribution by disc centrifuge photosedimentometry 橡膠配合劑－碳黑－聚集體粒徑分布之測定(圓盤離心沉降光測定法) |
|
|
|
CNS 11399
2017 Edition Method of StrAight-Beam Ultrasonic Test for Steel Plate for Pressure Vessel Use 壓力容器用鋼板直束法超音波檢驗法 |
|
|
|
CNS 503
2017 Edition ISO Metric Fine Screw ThreAds (Diameters from 18 to 150mm and Pitch 2mm) 公制細螺紋6（ISO制）（標稱直徑18至150公釐，螺距2公釐） |
|
|
|
CNS 7003
2017 Edition MAchine Taper Pin Reamers with Morse Taper Shanks 推拔銷鉸刀（莫氏圓錐柄，機用） |
|
|
|
CNS 14140
2017 Edition ReliAbility and lot control tests for transmitter and receiver modules used for wireless infrared communication 無線通信用紅外線傳輸和接收模組之可靠度及批品質控制測試 |
|
|
|
CNS 3884
2017 Edition SurfAce Treatment for Bicycle Parts 自行車（腳踏車）零件表面處理 |
Translated |
|
|
CNS 5298
2017 Edition Hose ClAmps for the Lower Pressure 低壓軟管夾 |
|
|
|
CNS 9234
2017 Edition Method of Test for Dry Reed Switches (StAndard Test Coils, Single Insulation 130 ℃ Wire) 乾式簧開關檢驗法（１３０℃單層絕緣線標準試驗線圈） |
|
|
|
CNS 12854
2017 Edition Fire Fighting Equipment for Liquefied Petroleum GAs Plant Use 液化石油氣設施用消防設備 |
|
|
|
CNS 15115
2017 Edition Thin-film terrestriAl photovoltaic (PV) modules - Design qualification and type approval 薄膜陸上型太陽光電模組－設計確認和型式認可 |
|
|
|
CNS 13020
2017 Edition Method of RAdoigraphic Test for the Welds of Steel Structure 鋼結構銲道射線檢測法 |
|
|
|
CNS 14109-2
2017 Edition Microfilming of technicAl drawings and other drawing office documents--Part2:Quality criteria and control of 35mm silver gelatin microfilms 技術類製圖和其他規格化製圖文件之微縮--第二部:35mm銀鹽軟片的品質規範與控制 |
|
|
|
CNS 10699
2017 Edition Method of Test for LAnd Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Sensitivity, Temperature and High Humidity) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻靈敏度、溫度及高濕度） |
|
|
|
CNS 14491
2017 Edition MAnipulating industrial robots-Performance criteria and related test methods 工業用機器人-性能準則與相關試驗法 |
|
|
|
CNS 1132
2017 Edition Pliers And nippers - Diagonal cutting nippers 夾鉗與剪鉗－對口剪鉗（平口鉗） |
|
|
|
CNS 12083
2017 Edition Method of Test for Fiber Optic Devices (FOPT-33 Fiber Optic CAble Tensile Loading and Bending Test) 光纖裝置檢驗法（光纜拉力負載與彎曲試驗ＦＯＴＰ–３３） |
|
|
|
CNS 4731
2017 Edition Knurled Nuts for DrAwing Instruments 滾紋螺帽（製圖儀器用） |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [301] [302] [303] [304] [305] [306] [307] |
